manualshive.com logo in svg

CENTURY PRODUCTS Ninja Pro, Instruction Manual

Share
Download
CENTURY PRODUCTS Ninja Pro Instruction Manual Download Page 10

Step 8 Mating The Upper and Lower Main Frames
Find the four 26 mm long threaded aluminum spacers (2002-093 Bag #3).  Fit them in-between the upper side frames
in the locations shown in the drawing.

Mate the upper frame assembly onto the lower frame assembly.  Fit the clutch bell onto the clutch first.  Add eight 14
mm long aluminum spacers (2002-089 Bag #3) in-between the upper and lower side frames.  See drawing for their
locations.  Use eight M3x25 bolts to go through these eight spacers.  Then add two M3x8 bolts to the two spacers that
are on the pulley bearing block.  Use blue Locktite on these bolts.

Ninja Pro don’t forget the engine starting belt (2002-109 Bag #4)  Or if building a Pro Master don’t forget to grease the
uniball at the base of the start shaft.

093

089

091

089

093

089

093

089

093

089

093

089

089

109

M3X25

M3X25

M3X25

M3X25

M3X25

M3X25

M3X25

M3X25

M3X8

M3X8

1 0

1 0

1 0

1 0

1 0

Summary of Contents for Ninja Pro





























Reviews:

No comments

Brands by name

Popular brands

Load more brands