manualshive.com logo in svg

Central States Centra Series, Assembly Instructions Manual

Share
Download
Central States Centra Series Assembly Instructions Manual Download Page 18

C E N T R A L   S T A T E S   M A N U F A C T U R I N G ,   I N C .

E f f e c t i v e   0 1 / 2 0 2 1   •   I n f o r m a t i o n   s u b j e c t   t o   c h a n g e   

18

STEP 1

Note: Place level on all girt clips throughout installation to ensure level girts.

1. Layout (2) PURLIN52 sidewall columns for column A.
2. Attach (1) PLATE43 using FAST54.
3. Attach (4) PLATE35 with PLATE45 between columns as shown using FAST54.
4. Attach (1) PLATE42 with (2) PURLIN52 using FAST54 as shown.
5. Repeat these steps for Column F.
6 Set assembled columns aside for later use.

Assemble Columns A and F

DIRECTIONS

REQUIRED PARTS
(4) PURLIN52
(2) PLATE43
(4) PLATE45
(2) PLATE42
(8) PLATE35
FAST54

PLATE43

PLATE35

PLATE45

PLATE42

PURLIN52

2

X

Note: To ensure building is 
square, do not fully tighten 
bolts until after STEP29.

Summary of Contents for Centra Series













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands