Central Machinery 33497 Owner'S Manual & Safety Instructions Download Page 10

Page: 10 / 12

Page 10

For technical questions, please call 1-888-866-5797.

Item 33497

FETY

OPERA

MAINTENANCE

SETUP

Troubleshooting

TO PREVENT SERIOUS INJURY:

Use caution when troubleshooting a malfunctioning Jack.

Completely resolve all problems before use.

If the solutions presented in the Troubleshooting guide do not solve

the problem, have a qualified technician inspect and repair the Jack before use.

After the Jack is repaired: Test it carefully without a load by raising it and lowering it fully, checking for

proper operation, BEFORE RETURNING THE JACK TO OPERATION.

DO NOT USE A DAMAGED OR MALFUNCTIONING JACK!

POSSIBLE SYMPTOMS

PROBABLE SOLUTION

(Make certain that the Jack is not

supporting a load while attempting

a solution.)

Jack will not

function at

its weight

capacity

Saddle

lowers

under

load

Pump

stroke

feels

spongy

Saddle will

not lift all

the way

Handle

moves up

when Jack

is under

load

Oil

leaking

from filler

plug

Check that Release Valve is closed fully.

Valves may be blocked and may not

close fully. To flush the valves:
1. Lower the Saddle and securely

close the Release Valve.

2. Manually lift the saddle

several inches.

3. Open the Release Valve and force the

saddle down as quickly as possible.

Jack may be low on oil. Check

the oil level and refill if needed.
Jack may require bleeding - see

instructions on page 8.

Unit may have too much

hydraulic oil inside. Check oil

level and adjust if needed.

Parts List and Diagram

Parts List

Part

Description

Qty

Upper Beam

Nut M12

Bolt M12

x110

Spring

Bottle Jack

Eye Bolt

Jack Plate

Nut M8

Arbor Plate

Part

Description

Qty

Press Apron

Support Pin

Bolt M10

Nut M10

Base Support

Frame Post

Spreader

Jack Handle

Record Product’s Serial Number Here:

Note:

If product has no serial number, record month and year of purchase instead.

Note:

Some parts are listed and shown for illustration purposes only, and are not available

individually as replacement parts. Specify UPC 792363334976 when ordering parts.

Summary of Contents for 33497













Search results

Summary of Contents for 33497

Reviews:

Related manuals for 33497

Brands by name

Popular brands

Central Machinery 33497, Owner'S Manual & Safety Instructions

Search results

Summary of Contents for 33497

Reviews:

Related manuals for 33497

Brands by name

Popular brands