background image

Page 4

For technical questions, please call 1-888-866-5797.

Item 62374 

        

SAFETY

O

PERA

TION

M

AINTENANCE

SETUP

Service

Have your Power Pack serviced by a qualified repair person using only identical replacement parts. 

  

This will ensure that the safety of the Power Pack is maintained.

Power Pack Safety Warnings

1. 

Lead-acid batteries generate hydrogen gas when 

charging.

  Hydrogen gas is explosive.  Only use 

the Jump-Start system in a well-ventilated area.

2. 

Jump Starting A Vehicle

a.  Use the Power Pack for jump starting 

a LEAD-ACID battery only. 

b.  For emergency use only.  Do not use the Power 

Pack as a replacement for a vehicle battery.

c.  Be sure area around battery is well ventilated 

while battery is being jump started.

d.  NEVER jump start a frozen battery.
e.  Do not attempt to jump start a vehicle with 

a non-rechargeable or defective battery.

f.  Study all battery manufacturer’s specific 

precautions for jump starting.

g. 

DO NOT TOUCH POSITIVE AND NEGATIVE 

BATTERY CLAMPS TOGETHER.  

h.  Unplug the Power Pack from its Adapter 

before connecting its cables to a battery.

i.  Connect and disconnect battery cable 

clamps only after setting any Jump Starter 

switches to OFF position.

j.  Connect cables to proper polarities.  Connect 

black cable to negative body ground and 

red cable to positive battery terminal.

k.  Locate Power Pack as far away from 

battery as battery cables permit.

3.  Maintain labels and nameplates on the Power Pack.   

These carry important safety information.   

If unreadable or missing, contact 

Harbor Freight Tools for a replacement.

4.  WARNING: This product contains lead, a chemical 

known to the State of California to cause cancer 

and birth defects or other reproductive harm.  

(California Health & Safety Code § 25249.5, 

et seq.

)

5.  WARNING: This product contains or, when 

used, produces a chemical known to the State 

of California to cause cancer and birth defects 

or other reproductive harm.  (California Health 

& Safety Code § 25249.5, 

et seq.

)

6.  WARNING: The cord of this product contains 

lead, a chemical known to the State of California 

to cause cancer, and birth defects or other 

reproductive harm. Wash hands after handling.  

(California Health & Safety Code § 25249.5, 

et seq.

)

7.  The warnings, precautions, and instructions 

discussed in this instruction manual cannot 

cover all possible conditions and situations 

that may occur.  It must be understood by the 

operator that common sense and caution are 

factors which cannot be built into this product, 

but must be supplied by the operator.

 SAVE THESE INSTRUCTIONS.

Specifications

Cranking Amps

330

Battery

12VDC, 17Ah

Battery Cables

42″ L

Maximum Air Pressure

250 PSI

Functions:  12 Volt Jump-Starter, Air Compressor,

12VDC Power Supply, and 3 LED Work Light

Specification

Summary of Contents for 62374













Reviews: