background image

Page 8

For technical questions, please call 1-888-866-5797.

Item 66967

Operating Instructions

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the 

beginning of this manual including all text under subheadings therein 

before set up or use of this product.

1.  Place the Power Inverter on a flat 

surface that has adequate ventilation 

and is not in direct sunlight.  Locate 

the Inverter close enough to the car 

battery so that the Cables can easily 

reach the Inverter and the car battery. 

Position the Inverter so that the Outlets 

are easily and safely accessible.

2.  To connect the Cable Ring 

Terminals to the (Positive) red and 

(Negative) black Power Terminals 

on the back of the Inverter:
a.  Make sure the Inverter’s 

Power Button is in the OFF position.

b.  Unthread the knobs covering 

the Power Terminals. 

c.  Slide the red Cable’s Ring 

Terminal over the post of the red 

Power Terminal and the black 

Cable’s Ring Terminal over the 

post of the black Power Terminal.

d.  Replace the knobs and 

tighten securely.

WARNING!

  Use only the included cables 

or 4 AWG cables up to 10 feet long.  

Thinner/longer cables may cause 

overheating and damage the inverter 

and/or connected devices.
3.  Apply the parking brake to the 

vehicle connected to the battery. 

Place the transmission in “Park” 

for an automatic transmission, 

or in “Neutral” for a manual 

transmission. Start the car engine.

4.  Attach the red Cable’s Alligator Clip 

to the Positive (red) terminal on the 

battery, then attach the black Cable’s 

Alligator Clip to a clean unpainted metal 

part of the chassis.  If connecting to 

a battery not installed in a vehicle, 

connect to the Negative (black) terminal.

5.  The red Fault LED will light up 

momentarily and the alarm will 

sound as the Inverter draws power. 

Then the alarm and red LED will turn off. 

Note:

 If the alarm continues and 

red Fault LED stays lit, check the 

Troubleshooting Tips section near 

the end of this manual to correct 

the issue before continuing.
6.  Press the Power Button to 

turn on the inverter.

7.  To power each device or appliance:

a.  With the device or appliance 

switched off, plug it into one of the 

Power Outlets or the USB Outlet 

on the Power Inverter. 

b.  Turn on the device and/or appliance. 

8.  After use, turn all connected devices 

or appliances off, unplug them, then 

turn off the car engine if it is running. 

Keep the inverter turned on and remove 

the alligator clips from the battery 

posts, removing the Negative (black) 

clip first, then the Positive (red) clip. 

The alarm and red LED light will turn 

on as the Inverter powers down. 

Turn off the Inverter Power Button.

Summary of Contents for 200 watt continuous













Reviews: