9
ENGLISH
Do not apply pressure to or stab at the touch button, a light touch using a bare finger is
sufficient. The command pulse is sent when the finger releases the button.
2.8) Battery status
The battery is equipped with LED indicators that indicate the remaining battery life at any time
by pressing the adjacent button (P) (Ref. to Fig. 1):
4 LEDs illuminated: fully charged
2 LEDs illuminated: 50 % capacity
1 LED flashing: minimum charge, replace the battery
With the battery inserted in the tool, the remaining battery
life can also be checked on the display, via touch button
selection (Ref. to section 4).
The screen shown alongside indicates that the battery Voltage has
dropped below a minimum safety threshold; under these conditions the
tool will not start, and it is necessary to recharge or replace the battery.
The approximate time to fully recharge a battery is about 40 minutes.
2.9) Using the battery charger
Carefully follow the instructions in the battery charger user manual.
3. MAINTENANCE
The tool is robust, completely sealed, and requires very little daily maintenance. Compliance with
the following points, should help to maintain its optimum performance:
3.1) Thorough cleaning
Dust, sand and dirt are a danger for any hydraulic device.
Every day, after use, the tool must be wiped with a clean cloth taking care to remove any residue,
especially close to pivots and moveable parts.
Do not use hydrocarbons to clean the rubber parts.
3.2) Storage case
When not in use, the tool should be stored and
transported in the plastic case supplied to prevent
damage. The case, type
VAL-P63
, is suitable for stor-
ing the tool, the accessories, up to 12 die sets and
pre-prepared compression connectors.
VAL-P63: Size 620x360x138 mm (24.4x14.2x5.4 in-
ches) an weight 2,6 kg (5.7 lbs).
P
p
= 325 bar
P
p
= 547 bar
RESET
SW:S1J96902
LED
OFF
ERROR
001
15001
BATTERY
P
n
= 742 bar
002
003
BATTERY
004
LED
ON
LED
OFF
LED
ON
max.
BATTERY
BATTERY
min.
B600ND
20AR112
10
14990
BATTERY
max 90°
90°
OK
P
n
= 742 bar
P
p
= 742 bar
RESET
SW:S1J96902
P
m
= 742 bar
P
= 0 bar
P
m
= 10762 psi
LED
ON
LED
OFF
*
1
*
2
*
3
*
4
*
5
*
6
*
7
8
9
10
11
12
P
= 0 psi
P = 0 bar
P
= 0 bar
P
n
= 742 bar
P
= 0 bar
BEEP
BEEP
P
n
= 742 bar
OK
Fm = 67.4 kN
OK
F
m
= 67.4 kN
F = 0.0 kN
F
m
= 7.57 ton
F = 0.00 ton
F
m
= 67.4 kN
F
p
= 67.3 kN
F
m
= 134.3 kN
OK
P
m
= 742 bar
P
p
= 741 bar
P
m
= 742 bar
OK
P
p
= 325 bar
P
p
= 547 bar
RESET
SW:S1J96902
LED
OFF
ERROR
001
15001
BATTERY
P
n
= 742 bar
002
003
BATTERY
004
LED
ON
LED
OFF
LED
ON
max.
BATTERY
BATTERY
min.
B600ND
20AR112
10
14990
BATTERY
max 90°
90°
OK
P
n
= 742 bar
P
p
= 742 bar
RESET
SW:S1J96902
P
m
= 742 bar
P
= 0 bar
P
m
= 10762 psi
LED
ON
LED
OFF
*
1
*
2
*
3
*
4
*
5
*
6
*
7
8
9
10
11
12
P
= 0 psi
P = 0 bar
P
= 0 bar
P
n
= 742 bar
P
= 0 bar
BEEP
BEEP
P
n
= 742 bar
OK
Fm = 67.4 kN
OK
F
m
= 67.4 kN
F = 0.0 kN
F
m
= 7.57 ton
F = 0.00 ton
F
m
= 67.4 kN
F
p
= 67.3 kN
F
m
= 134.3 kN
OK
P
m
= 742 bar
P
p
= 741 bar
P
m
= 742 bar
OK
P
p
= 325 bar
P
p
= 547 bar
RESET
SW:S1J96902
LED
OFF
ERROR
001
15001
BATTERY
P
n
= 742 bar
002
003
BATTERY
004
LED
ON
LED
OFF
LED
ON
max.
BATTERY
BATTERY
min.
B600ND
20AR112
10
14990
BATTERY
max 90°
90°
OK
P
n
= 742 bar
P
p
= 742 bar
RESET
SW:S1J96902
P
m
= 742 bar
P
= 0 bar
P
m
= 10762 psi
LED
ON
LED
OFF
*
1
*
2
*
3
*
4
*
5
*
6
*
7
8
9
10
11
12
P
= 0 psi
P = 0 bar
P
= 0 bar
P
n
= 742 bar
P
= 0 bar
BEEP
BEEP
P
n
= 742 bar
OK
Fm = 67.4 kN
OK
F
m
= 67.4 kN
F = 0.0 kN
F
m
= 7.57 ton
F = 0.00 ton
F
m
= 67.4 kN
F
p
= 67.3 kN
F
m
= 134.3 kN
OK
P
m
= 742 bar
P
p
= 741 bar
P
m
= 742 bar
OK
