background image

8

ENGLISH

2.7) Battery status

  The battery is equipped with LED indicators that indicate the 

  remaining battery life at any time by pressing the adjacent 
 button 

(P):

  4 LEDs illuminated: fully charged
  2 LEDs illuminated: 50 % capacity
  1 LED flashing: minimum charge, replace the battery.

  

Worklights (4) illuminated combined with an alarm audible when the operating button (5)

        is pressed (Ref. to Fig. 3), indicate that the battery voltage has dropped below a minimum
        safety threshold. Under these conditions the tool will not start, and it is necessary to recharge 
or replace the battery. The approximate time to fully recharge a battery is about 40 minutes.

2.8)  Using the battery charger

  Carefully follow the instructions in the battery charger user manual.

3.   MAINTENANCE

The tool is robust, completely sealed and requires very little daily maintenance. Compliance with 
the following points should help to maintain its optimum performance:

3.1) Thorough cleaning

  Dust, sand and dirt are a danger for any hydraulic device. Every day, after use, the tool must be 

  wiped with a clean cloth, taking care to remove any residue, especially close to pivots and move-
 able 

parts.

  Do not use hydrocarbons to clean the rubber parts.

  Regularly lubricate the moving parts and pivot pins of the head with a few drops of oil.

3.2)  Cleaning of the rubber handgrip

  To avoid the accumulation of swarf inside the rubber handgrip, (3) periodically fold back the 

  handgrip near the blades and carefully brush out any debris.

3.3) Storage case

  When not in use, the tool should be stored and transported in the metal case to prevent damage. 

     Metal case: VAL-P59, size 620x360x138 mm (24.4x14.2x5.6 in.), weight 2,4 kg (5.3 lbs).

3.4) Routine maintenance 

When the tool reaches the predetermined number of hours worked, it will signal that routine 
maintenance is recommended. 

  

  

 

The tool will continue to work, however 15 sec. after use an alarm comprising 3 beeps com-

        bined with illumination of the worklights will signal that its return to 

Cembre

 for service is 

        recommended  (see § 6).

ENGLISH

P

Summary of Contents for B-TC500ND-SC

































Reviews: