manualshive.com logo in svg

Cedar Summit STONEYCREEK CEDAR PLAYHOUSE P280090, Installation And Operating Instructions Manual

Share
Download
Cedar Summit STONEYCREEK CEDAR PLAYHOUSE P280090 Installation And Operating Instructions Manual Download Page 35

Instructional video:  http://www.cedarsummitplay.com/install-stoneycreek

 

35 

 

    

[email protected]   

Fig. 10.7

Hardware

Fig. 10.6

Outside View

Side Wall

Inside/Underneath View

Fig. 10.8

S37

Step 10:  Bay Window Assembly 

Part 3

D:

  From outside the assembly place Bay Window Top on top of Bay Window Insert and under the wall panel then 

attach to Bay Window Insert with 4 (S37) #7 x 5/8” Pan Screws.  (fig. 10.6, 10.7 and 10.8)

E:

  Attach Bay Window Top to the Side Wall with 4 (S37) #7 x 5/8” Pan Screws.  (fig. 10.8) 

Outside View

Bay 

Window 

Top

Bay Window 

Insert

Side Wall

S37

Bay Window Top

Side Wall

8 x 

#7 x 5/8” Pan Screw

Other Parts

S37

1 x Bay Window Top

S37

S37

Bay Window Top

Bay Window 

Insert

Summary of Contents for STONEYCREEK CEDAR PLAYHOUSE P280090





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands