manualshive.com logo in svg

Cedar Summit STONEYCREEK CEDAR PLAYHOUSE P280090, Installation And Operating Instructions Manual

Share
Download
Cedar Summit STONEYCREEK CEDAR PLAYHOUSE P280090 Installation And Operating Instructions Manual Download Page 18

Instructional video:  http://www.cedarsummitplay.com/install-stoneycreek

 

18 

 

    

[email protected]   

Step 3:  Counter Assembly 

Part 1

A:

  Flush to each end and to the bottom of (031) Counter Back attach 1 (033) Counter Joist per end with 1 (S2) #8 

x 1-1/2” Wood Screw per joist.  Notice the holes at the top of (031) Counter Back.  (fig. 3.1 and 3.2)

B: 

 Place the remaining 3 (033) Counter Joists centred over the pilot holes in the middle of (031) Counter Back 

and flush to the bottom of the board.  In the bottom holes attach with 1 (S2) #8 x 1-1/2” Wood Screw per joist.  (fig. 

3.1 and 3.2)

C: 

 Place (032) Counter Front against (033) Counter Joists so the ends are flush and the centre (033) Counter 

Joists are centred over the pilot holes.  Measure 5/8” down from the top of (032) Counter Front on both ends and 

attach to the (033) Counter Joists with 5 (S2) #8 X 1-1/2” Wood Screws.  (fig. 3.1 and fig. 3.2)

Wood Parts

Hardware

10 x 

 #8 x 1-1/2” Wood Screw

S2

1 x 

Counter Back 5/8 x 3-1/4 x 41-3/4”

1 x 

Counter Front 5/8 x 2-3/4 x 41-3/4”

5 x 

Counter Joist 1 x 2 x 8-1/4”

031

032

x 5 per side

Fig. 3.1

032

S2

031

031

Flush

033

Fig. 3.2

032

033

Notice hole 

locations

033

033

5/8”

Summary of Contents for STONEYCREEK CEDAR PLAYHOUSE P280090





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands