background image

Cappuccino Dispenser - Vertical Door

Cecilware

®

5

Water Inlet Connection:

NOTICE: 

This equipment is to be installed to comply

with the applicable Federal, State, or local plumbing
codes having jurisdiction. In addition:
1.  A quick disconnect water connection(s) or enough

extra coiled tubing (at least 2x the depth of the
unit) so that the machine can be moved for cleaning
underneath.

2. An approved back flow prevention device(s), such

as a double check valve must be installed between
the machine and the water supply.

The GB beverage dispenser is equipped with a ¼" Flare
Water Inlet fitting which is located on the back of the
unit. GB8M10-LD-U is equipped with (2) ¼" Flare Water
Inlet fittings.

Water pipe connecting and fixtures directly connected
to a potable water supply shall be sized, installed, and
maintained in accordance with Federal, State, and Local
codes.

HIGHLY RECOMMENDED: 
A WATER SHUT-OFF VALVE and A WATER FILTER,
preferably a combination Charcoal/Phosphate Filter, to
remove odors and inhibit lime and scale build up in the
machine. 

NOTICE:

In areas with extremely hard water, a water

softener must be installed in order to prevent a
malfunctioning of the equipment and in order not to
void the warranty. 

Electrical Connection

PLUG CONFIGURATIONS
The GB8 MODEL is supplied from the factory with two
(2) 120 volt electrical cords and plugs installed. Plugs are
supplied according to the application as shown below:

GB3 and GB6 are supplied with one cord and plug.

Unpacking Instructions

Carefully unpack the GB Machine and inspect
immediately for shipping damage. Your GB Machine
was shipped in a carton designed to give it maximum 
protection in normal handling. It was thoroughly
inspected before leaving the factory. In case of damage,
contact the shipper, not Grindmaster-Cecilware.
After the machine has been unpacked and placed on a
counter, pull out the stainless steel drip tray. It should
contain the following:

• Water Inlet Fitting(s)

&83

*%0/'8
*%03/'8

8 Flavor Cappuccino Dispenser

Upper Door open, Lower Door not shown.

&83

*%0/'8
*%03/'8

6 Flavor Cappuccino Dispenser

Upper Door open, Lower Door not shown.

3/8*&21),*85$7,21

1(0$3

1(0$5

1(0$2

1(0$2

 '(',&$7('287/(769$

)LJXUH

)25*%0 *%0321/<

Installation (continued)

Description and Location of Components

CAUTION

Lifting hazard. Single person lift could

cause injury. Use assistance when moving or lifting.

Summary of Contents for GB3M-10-LD-U

























Reviews: