Cecilware FE-100G Operation Manual Download Page 2

 

2

SAFETY PRECAUTIONS 

FOR YOUR SAFETY, THE FOLLOWING SAFETY PRECAUTIONS SHOULD  

BE FOLLOWED AND ENFORCED. 

 
IF YOU SMELL GAS: 

 

OPEN WINDOWS                                         

 

DON’T TOUCH ELECTRICAL SWITCHES  

 

EXTINGUISH OPEN FLAMES 

 

IMMEDIATELY CALL YOUR GAS SUPPLIER 

 

1. Instructions must be posted in a prominent location and all safety 
precautions taken in the event the user smells gas. Obtain this 
information from your local gas supplier. 
2.

 

LIGHTING: Follow the instruction on page 6 and label attached to 
right side of coffee urn.  

3.

 

Do not place anything over the flue opening. 

4.

 

Do not place combustibles or non-combustible materials in the 
proximity of coffee urn as this could cause fires or obstruct air flow to 
the main burners. 

5.

 

This installation must conform with local codes, or in absence of local 
codes with the National Fuel Gas Code ANSI Z223.1, latest edition. 

6.

 

Provide adequate air supply and ventilation.  

7.

 

Provide adequate clearance for air openings into the combustion 
chamber. 

8.

 

Provide clearance for servicing and proper operation. Minimum 
clearance from combustible construction 8” from back and 6” from 
side. 

9.

 

Boiler must be disconnected from gas supply during any pressure 
testing of pipelines in excess of ½ psig, and isolated (by turning off 
gas shut-off valve) during any testing less than ½ psig. 

10.

 

Retain this manual for future reference. 

 
 
UNPACKING INSTRUCTION: Carefully unpack the coffee urn and inspect 
immediately for shipping damages. Your automatic coffee urn was 
shipped in a carton designed to give maximum protection in normal 
handling. It was thoroughly inspected before leaving the factory and the 
carrier accepted and signed for it. File any claims for shipping damage or 
irregularities with the carrier. 
 
 
ELECTRICAL CONNECTIONS:    Cord Type Plug-in 
 

 

 

 

 

   120 VAC, 15 AMP, 50/60 Hz 

 

 

 

 

 

 

POWER REQUIREMENTS:  

   3 AMP @ 120 VAC, 50/60 Hz  

 
 
 

Summary of Contents for FE-100G












Reviews: