cec AMP3800 Owner'S Manual Download Page 5

AMP3800 User's Manual

Turning power ON: Turn AMP3800’s power ON at last, after turning ON the DA 

converter or CD-player connected to AMP3800.

Turning  power  OFF: Turn AMP3800’s  power  OFF  first,  before  turning  OFF 

connected units.

3. Handle with Care

Avoid exerting excessive force on the cabinet, the volume and selector knobs and 

the push switches of AMP3800.

4. Avoid Electrostatic Discharge

Like all complex electronic devices, AMP3800 is sensitive to electrostatic discharge. 

A discharge may cause malfunction or damage.

5. Installation
Use  of  an  audio  rack  is  recommended  to  maximize  the  sound  quality  and 
performance of AMP3800. Installation and use of AMP3800 in the locations 
described below may cause deterioration in sound quality or malfunctions.

Locations exposed to direct sunlight, such as windowsills, and other exceptionally 

warm locations, such as near heating appliances (surrounding temperature higher 

than 35

), or exceptionally cold locations (surrounding temperature lower than 5

℃)

 

may prevent AMP3800 from functioning adequately.

Damp locations exceeding 90% humidity may cause AMP3800’s metal parts to 

rust, causing the unit to malfunction.

Dusty locations may cause AMP3800 to malfunction. The accumulation of dust 

outside and inside the unit may lower the performance of music signal amplification. 

It may also cause contact failure of the switches and/or noise.

Otherwise, avoid installing AMP3800 close to other transformers and electrical 

motors, so as to prevent the pickup of induction hum. Also, avoid mounting 

AMP3800 on surface that may be affected by vibration.

6. Avoid Lightning Strikes Damages
Disconnect the AC power cord from the AC outlet when there is a thunderstorm in 
your vicinity.

7. Condensation
When AMP3800 has been brought into a warm room when the exterior temperature 

is  cold,  or  when  the  room  temperature  rises  sharply  from  using  a  heater, 
condensation may occur from both inside and outside the unit, hampering its 
performance. If this happens, leave AMP3800 unused in the room for 1 to 2 hours 
(depending on the amount of condensation), so as to bring the unit’s temperature 

closer to the room temperature. The condensation should go away gradually.

8. Listening Etiquette

When adjusting the sound volume level, make sure you do not disturb other people 

and your neighborhood.

Summary of Contents for AMP3800


















Reviews: