background image

 

 

the dishwasher can be very hot when the programme is 

running. 

 

When the dishwasher is not in use, we recommend that 

you turn off the water supply at the supply tap and 

disconnect the main supply. 

 

If you are leaving the dishwasher for an extended period 

you should leave the door slightly open to prevent the 

formation of unpleasant smells. 

 

The plastic housing on the water inlet pipe contains an 

electrically operated valve. The wires that connect to this 

valve are inside the inlet hose. Do not cut through the inlet 

hose, and do not put the plastic housing in water. 

 

Children could get locked inside the appliance. Therefore 

when disposing of an old appliance, cut off the plug and 

set aside, and damage the door lock so that the door can 

no longer be closed. 

 

Recommendations 

 

To reduce energy and water consumption, remove all dirt 

residues from the dishes prior to loading the dishwasher. 

 

Only run the dishwasher when fully loaded. 

 

Place hollow items (bowls, glasses and pans) face down in 

the basket. 

 

Do not put dishes or cutlery with tobacco ash, wax, 

lubricating grease or paint residues in the dishwasher. 

 

Before First Use 

 

Set the water softener level as required by the water 

hardness in the area. 

 

Add 1kg of salt into the salt compartment and then fill with 

water to the top of the salt compartment. 

 

Remove all the packaging materials from the interior of the 

dishwasher. 

 

Fill the rinse aid compartment. 

Summary of Contents for wc431





























Reviews: