background image

 

10 

 

25 cm

3

, to be used depending on how dirty the dishes are.  

If your dishes are in need of an intensive wash, then add 5 

cm

3

 of detergent into the prewash section of the 

compartment 

a

 (figure 1). 

3.

 

Then close the detergent compartment lid until the latch 

locks. 

 

Please note: You should only use detergents designed 

specifically for use in dishwashers. 

 

Combination detergents (e.g. 3-in-1 tablets) must not be used in 

any quick wash or half load programme. 

 

If using dishwasher tablets, always use the detergent  

compartment, do not put them in the main body of the dishwasher 

or in the cutlery basket. The solubility of dishwasher tablets can 

vary depending on the temperature and duration of the 

programme. As a result, it is recommended that powder 

detergents should be used in the shorter programmes to allow 

better performance. 

 

CDA recommends the use of separate detergent, rinse aid and 

dishwasher salt rather than combination tablets as separates 

achieve better wash performance. 

 

If you do use combination detergents, add salt and rinse aid to the 

dishwasher and then adjust the water hardness setting and rinse 

aid setting to the minimum.  When you then use separate 

detergents again, you should fill the salt and rinse aid 

compartments, adjust the water hardness setting to the maximum 

and run an empty wash, then adjust the water hardness setting 

and the rinse aid setting to the appropriate level. 

 

 

 

 

Summary of Contents for wc431





























Reviews: