background image

Salt

.3.

Salt

The hardness of the water varies from place to place. If hard

water is used in the dishwasher, deposits will form on the dishes

and utensils.

The appliance is equipped with a special softener that uses a salt

specifically designed to eliminate lime and minerals from the water.

Loading the Salt into the Softener

Always use salt intended for use with dishwashers.

The salt container is located beneath the lower rack and should

be filled as follows:

- Remove the lower rack and then unscrew and remove the cap

  from the salt container;

- If you are filling the container for the first time, fill it with water;

- Place the end of the funnel (supplied) into the hole and intro-

  duce about 2 kg of salt. It is normal for a small amount of water

  to come out of the salt container.

- Carefully screw the cap back on.

The salt container must be filled when the "low salt" indicator

light (located on the control panel), comes on..

To prevent the formation of rust, load the salt just be-

fore beginning a wash cycle.

Adjusting Salt Consumption

The dishwasher is designed to allow for adjusting the amount of

salt consumed based on the hardness of the water used. This is

intended to optimize and customize the level of salt consump-

tion so that it remains at a minimum.

To adjust salt consumption, proceed as follows:

- Unscrew the cap from the salt container;

- There is a ring on the container with an arrow on it (see figure

  to the side),

- If necessary, rotate the ring in an anticlockwise direction from

  the "-" setting  towards  the  "+" sign, based on the hardness of

  the water being used.

  It  is  recommended  that adjustments be made  in accordance

  with the following schema:

Water Hardness

Clarke

degrees

˚dH

mmol/l

Selector

position

Salt
consumption
(Grams/cycle)

Autonomy
(cycles/2kg)

0

14

M

NT

NIU

QIQ

NU

QQ

NQ

PS

PS

TN

QR

UV QIR

UIV

[UV

[TN

[UIV

L

?J?

jba

L

M

OM

QM

SM

?H?

SM

QM

OR

M

NIT

GB

Summary of Contents for CW495
















Reviews: