CCTV SYSTEM
34
Preset
Speed dome / camera control content
Call preset
Set preset
91
Set the soft address
¤
92
Switch from soft address, protocol, baud rate to hardware
address set and automatic identification protocol, baud rate
¤
91
Open communication protocol automatic identification
¤
92
Automatic identification of communication protocol to shut
¤
93
Restore factory settings
¤
93
Delete all presets
¤
94
PTZ recalibrate
¤
95
Open OSD menu of speed dome
¤
¤
107
start the automatic flip
¤
107
Close the automatic flip
¤
108
PTZ speed / Lens turn times match open automatically
¤
108
PTZ speed / Lens turn times match close automatically
¤
143
Setting the PTZ slow down 2 times corresponding to the
zoom
¤
144
Setting the PTZ slow down 4 times corresponding to the
zoom
¤
145
Setting the PTZ slow down 8 times corresponding to the
zoom
¤
130
Set the PTZ low speed
¤
131
Set the PTZ Middle speed
¤
132
Set the PTZ high speed
¤
135
Set video output formats into PAL
¤
136
Set video output formats into NTSC
¤
138
Open the alarm function
¤
138
Close the alarm function
¤
139
Open the alarm output
¤
139
Close the alarm input
¤
2.
Dome Controlling Function Express
3.
Camera Function Express
109
Open the camera menu
¤
109
Close the camera menu
¤
127
The protocol of the camera settings( set preset 127+ set
preset 1-7 number , preset 1-7 corresponding SAN-
SUNG/LG/HITACHI/LGE/SANYO/CNB)
¤
104
Set the lens ZOOM current position corresponding to
multiple relationship
¤
104
Set the lens ZOOM current position corresponding to
multiple relationship
¤
106
Turn on the speed dome of camera initialization
¤
106
Turn off the speed dome of camera initialization
¤
IR Intelligent Speed Dome Operation Manual ver2.0
11
Step c. Set speed dome
(1) Set (DIP switches) SW2 under the bottom of dome machine
to control speed dome IP address. (Detailed information can
be found in PART 12
)
(2) Without SW2 DIP switches ,setting the IP address by soft-
ware address
refer to Page21
【
Communication settings
】
Step d. Install the speed dome core
(1). Hold the module with a hand, put the 2 waist-holes at the
module bottom accordingly into the 2 screws of top bracket,
and screw it to the bottom of the waist-holes. Screw the 2
screws firmly with a screwdriver.
Figure
（
12
）
figure
（
13
）
figure
（
14
）
figure
（
15
）
figure
（
16
）
4
、
Pillar installation of dome
：
Step a. Install pillar accessory
(1) Put the line though the pillar accessory and fix it with hose
clamps.
(2) Install
the
dome
on
the
bracket
;
fix
it
tightly
with
a
3PCS
screw.
(3) Put the line though the wall bracket and fix it with column
accessory together. ( Shown as figure 15)
※
NOTE: If the machine is installed outside, seal
the speed dome to be water proof.
①
Tape around the joint, and then fasten the housing.
②
make sure the joint with silica gel to be waterproof
Step b. Install wall bracket
(1) Put the line though the wall bracket and fix it with column
accessory together as figure 16 shows.
Step C. Set driver of dome:
refer to the drive setting of wall-
hung dome on Page 10
Step D. Install the module
: refer to the installation of wall-
hung dome module on Page 10
Step E. Install the lower housing
: refer to the installation of
lower housing of wallhung dome on Page 10
Step e. install dome
(1). Insert two setscrews which are in the bottom of dome into
the waist-shape holes in top mount and turn the mount to
make sure that two screws are in the positioning slot.
