55
4
Selecting the Lighting Mode
3
Setting the light Intensity
7
Manual Control
Make sure that the main power source is turned ON.
Set items , , and when using Continuous Mode or ON/OFF Mode.
Set items , , , and when using Strobe Mode.
1
3
4
2
1
3
2
Make sure that the LOCK setting indicator is
not light and that the trigger logic switch is set
to HIGH. Otherwise you may not be able to
perform the rest of this procedure.
Set the Manual/External Mode Selector to MANU to
set Manual Mode.
1
Setting the Manual/External Mode Selector to Manual
Check
Four channels from L1 to L4 are
allocated to the 24V LIGHT and HLV
LIGHT output connectors. When L1 is
selected, settings for the L1 Light Unit
for the 24V LIGHT connectors and the
HLV LIGHT connectors can be
changed. The 4 channels can be
controlled separately.
2
Selecting the Channel
Press the channel selection switch to select the channel to set (L1 to L4).
Only channels with Light Units connected to them can be selected.
(If a new Light Unit is connected, the lowest channel is automatically selected.)
Press.
Press the setting switch to light the PLS setting indicator.
Turn the setting switch to select the lighting mode from Continuous Mode,
ON/OFF Mode, or Strobe Mode. (Default value:
F00
)
Press the setting switch to light the BRT setting indicator.
Turn the setting switch to set a value between 0 and 255.
(Default setting:
255
, Minimum:
000
, Maximum:
255
)
Press.
Press.
* The light intensities are theoretical values.
24V LIGHT
0.4
(Dimly lit)
0.8
1.2
99.6
100.0
…
Light intensity (%)
HLV LIGHT
0.0
(Not lit)
0.4
0.8
99.6
100.0
…
…
000
002
254
255
001
Digital Window
Locking Settings
When the setting switch is pressed for 2
seconds or longer, the lighting mode and
light intensity settings are locked, and the
LOCK setting indicator lights. (The set values
can be viewed.) Pressing the switch again for
2 seconds or longer releases the lock.
4
Selecting the Lighting Mode (Continued)
Turn the setting switch and set
F00
to turn ON the Light Units continuously.
To flash the strobe, turn the setting switch and select a setting from
F01
to
F10
(strobe time of 40 μs to 40 ms). The Light Units are turned ON for the
period of time set on the setting switch after the external trigger signal is input.
The Strobe Mode can be set for 24V DC Light Units only.
Turn the setting switch and set
F00
to turn the Light Units ON and OFF.
The Light Units are turned ON or OFF according to the external trigger signal input.
40μs
80μs
120μs
200μs
600μs
Strobe Mode
(The Strobe Mode can be set
for 24V DC Light Units only.)
1ms
4ms
10ms
20ms
40ms
Continuous Mode / ON/OFF Mode
Status
Digital Window
F01
F02
F03
F04
F05
F06
F07
F08
F09
F10
F00
Press for 2 s.
Continuous Mode
ON/OFF Mode
(If the external trigger is not used, the Light Units are ON continuously.)
Strobe Mode
(If an external trigger is not used, the Light Units are OFF.)
For details on the external trigger input, refer to 9. Inputting the External Trigger.
Precautions for Channel Selection
Only channels with Light Units connected to them can be selected. If a Light Unit is removed
without turning OFF the power supply, the channel for the Light Unit that is no longer connected
may be selected. This does not indicate a malfunction. Check the following table for details.
There is risk of fire or electric shock. Make sure that the power supply is turned OFF when
you connect Light Units or Spotlights.
The channel with the
disconnected Light Unit
can be selected.
The Light Unit was disconnected
without turning OFF the power supply.
The channel with the
disconnected Light Unit
cannot be selected.
Operation
If there is an electrical connection,
the Light Unit will light.
(The channel can be selected.)
The Light Unit does not turn
ON or an HLV ID error occurs.
(The channel cannot be selected.)
A Light Unit that is not
supported was connected.
Connector Connection Example
L2 and L4
Channels
can be selected for the
and
: L4
: L 2
.
can be selected if the connections
without turning OFF the power supply.
L1, L2 and L3
Channels
and
: L3
: L 1
.
are changed to the following:
following connections:
Even if the Light Unit is disconnected,
the channel can be selected until
the power is turned OFF.
(The settings are also retained.)
