background image

CCEI 

Limpido Z2

 

v1.0 

 

Page 10 

This display allows to set the volume of the pH liquid tank. 
The volume of the tank is adjustable from 0 to 25L. To enter it, press the button   and select the value using 
the buttons   and . 
 
To validate the set value, press the button . To leave the program without validation, press the button  . 
 
Comment: As 

Limpido Z2

®

 injects liquid in the pool, the previously set value is decremented. As soon as the 

value reaches 0, the 

Limpido Z2

®

 pump is blocked. To let the pump run again, the user has to set the level of 

the tank volume as described above. If the volume is set at 0, there is no control of the tank level.  
 

pH Calibration 

This menu is intended for the Ph probe calibration. This operation must be realized during the first starting up 
and then periodically as mentioned on Maintenance section.  
The calibration is done with two solutions delivered with the 

Limpido Z2

®

: pH7 solution and a pH9 solution. 

These  solutions  have  to  be  kept  closed  away  from  light  and  heat.  They  can  not  be  used  after  the  expiration 
date as it could induce measurement errors. 
 
To start calibration, press the button . 

Limpido Z2

®

 shows therefore Calib. pH7:x.x  ?. It means that the user 

must  plunge  the  probe  in  the  pH7  solution,  wait  for  a  stable  pH  value  (at  least  2  minutes)  and  press  the 
button .  If  the  value  is  correct,  the  calibration  procedure  continues;  if  not  the  Err. !  Message  flashes,  press 
then the button   to restart the measurement. 
 

Limpido Z2

®

 shows then Calibr. pH9:x.x?. You need to plunge the probe (

after rincing

) in the pH9 solution 

and press the key . 
 
If  the  calibration  has  been  successful,  the  pH  Calibration  message  is  shown.  On  the  contrary  if  the  message 
Err. !  appears,  repeat  the  calibration  procedure  after  checking  the  solution  and  the  probe.  If  the  problem 
remains, get in touch your installer. 
 

ELECTROLYSIS

 

M

ENU

 

With this menu you can configure the electrolysis settings.  
To accede to different settings, press the button . 
The menu can be operated by the keys   and . The various displays of this menu are as follows: 

  Production= THR 

With this display you can select the operating mode of the salt chlorinator. Press the button   and select the 
regulation mode using the keys  and  . 
 
The various possible modes of regulation are the following: 
-

 

PRG

: programmed: produces chlorine for a number of hours per day regardless of the measurement. 

-

 

THR:

  thermo  regulated:  in  this  mode  the  measured  temperature  by  the  cell  is  used  to  calculate  the 

necessary operation time. 

-

 

ON

: to produce permanently and without regulation. This mode can be used in case of failure of the ORP 

probe. The production is conditional upon the operation of the filtration pump.  

-

 

OFF

: to stop any chlorine  production by the salt chlorinator. This mode  can be  used during wintering  for 

example. 

 
To validate the mode, press the button . To leave the program without validation, press the button  . 

Prod/24h= 08h 

With this menu you can set up the required production time in PRG mode. In another mode, this value is not 
relevant. 
To  vary  this  value,  use  the  buttons 

  and .  To  validate  the  value,  press  the  button .  To  exit  the  program 

without validation, press the button . 

Prod Level = 80% 

Summary of Contents for Limpido Z2 25















Reviews: