www.cayken.com.cn
www.cayken.com.cn
11
12
C
AYKEN
PROFESSIONAL DRILLING
C
AYKEN
PROFESSIONAL DRILLING
10 Power line should be rubber cable used in line with national standards at the same time
the machine should be connected to the power leakage protection switch and guarantee
grounding reliable grounding
11 Installation or mobile machine must switch off the machine and then cut off the machine
power supply mobile magnetic base drill he should raise the magnetic base drill can not
drag on the operating surface damage to the antimagnetic seat or the workpiece surface
12 Not to cut off the power line or replace the plug so as to avoid the occurrence of circuit board
burned or magnetic seat burn
13 After the machine in a cumulative 300 hours of work should check whether you need to
replace the brush after 3 months of use to the machine safety inspection in maintenance
must use the original parts in order to enable the machine to achieve the best state at the
same time all about machine maintenance and inspection shall be conducted by professional
personnel to complete
14 Warning using non factory original accessories easy to cause the tool damage even pers-
onal injury
.
,
.
.
,
,
,
,
,
.
.
,
.
.
,
,
,
,
,
.
.
:
,
,
.
1 .Plug the power plug the drill bit aim at processing position make the magnetic switch is
opened so that the magnetic is adsorbed on the surface of steel plate magnetic materials
No impurities on the surface and check whether the attractive force is normal or not ge-
neral plate thickness should be more than 10mm
2 .Please placed the magnetic base drill required from the drilling near site and select the appro
priate adsorption material And will handle hole safety rope penetrates into the frame the
other one is in fastening frame after the penetration of the buckle and then close the safety
rope buckle Hand and pull off should not loose and mobile
3 .For a support screw regulating the support screw that the bottom touches the workpiece
surface
4. For the magnetic base is provided with the angle of the drill the use of angle wrench movem-
ent angle disk in the annex to the belt rack makes bit central alignment processing position
tighten the angle wrench
5 .Open the electric drill switch check whether the drill bit beat sound is normal if everything is
normal can turn the handle to feed
6. Start feeding should be slow gives the quantity of about 0 05mm r in general not too much
force to prevent overload
7. If the drill for kill suddenly stopped you must turn off the power switch immediately Must
close the magnetic control switch
8 Please shut down for a period of time machine in continuous use for 2 3 hours in case mag-
netic base is overheated and leakage or burned
,
,
,
.
,
. (
)
.
,
,
.
,
.
,
.
,
,
.
,
,
,
.
,
.
/
,
,
.
,
, (
)
.
-
,
.
MAGNETIC HOLLOW DRILL INSTRUCTIONS
Tool before connecting power, using the socket must be able to fit the plug machine. The
380V model to determine the fire and. Line the correct docking, power supply socket with the
need of professionals to complete. Do not arbitrarily change the plug, adapter plugs can't pick.
The electric tool wire used together.
1 Please read this manual carefully before using the magnetic drilling characteristics and rules
of operation the operator must go through specialized training fully understand before
operating the machine The machine can not be in the dust flammable explosive gas wor
king under the dangerous environment workplace should have good lighting conditions
kept clean and in an orderly
2 Please confirm the voltage volts before use high working voltage exceeds the rated voltage
of the 5
such as over will cause the motor burned or leakage accident resulting in pers
onal injury
3 Operating personnel must be absorbed in the work not only to keep a clear mind and more
rational operation Tired drinking or taking drugs stimulants drug do not operate the ma
chine when using power tools as long as a little distraction may occur for the serious cons
equences of accidents
4 To wear appropriate clothing operating the machine When you work mustn t be too loose
clothes wear jewelry Mustn t let the hair clothes gloves contact rotating parts on the ma
chine Loose clothing or jewelry long hair easy to tangle accident
5 Don t use electric tools must have the machine stored in children can not get Don t let un
familiar with machine operation method and don t read the manual people use the machine
6 Don t let internal motor with water ventilation hole can not be blocked when operating the
machine so as to avoid motor leakage or because of poor heat burned
7 Operating the machine please confirm the drilling position whether there is danger such as
power lines gas pipelines water pipe etc
8 The magnetic drill with a safety rope work on the walls and ceiling must fasten safety rope
at the same time the use of spray cooling tool And to drill down to the iron scurf should take
the corresponding protective measures
9 The magnetic base drill should be started in idle state prohibit starting with load so as not
to damage the magnetic base drill high altitude operations please note that the magnetic
fixed firmly to prevent the magnetic base drill down
.
,
,
.
,
,
-
,
,
.
.
,
+ %,
,
-
.
,
.
,
,
,
,
-
,
-
.
.
.
,
'
,
.
'
,
,
-
.
,
.
'
,
.
'
-
'
.
.
'
,
.
,
,
,
..
.
,
,
,
.
,
.
.
,
,
,
-
,
,
.
ELECTRICAL SAFETY
SAFETY INSTRUCTIONS
Attention: Our company does not assume any responsibility because the machine is not solid
or fixed safety facilities are not in appropriate place cause accident.