Alarm signal 2 (- - -) is a non life threatening
alarm, like a flooding alarm:
Smoke alarm signal:
--- --- ---
Heat alarm signal:
--- --- ---
Flood alarm signal:
- - -
CO alarm low level signal:
- - -
CO alarm high level signal:
--- --- ---
Please note that only the originating alarm’s LED
will flash, so it can be identified.
9.
PAUSE/HUSH FUNCTION:
If the smoke alarms are to set into a false alarm
by cooking, fireplace, etc. they can be paused for
10 minutes by pressing the test button on the
originating smoke alarm only (indicated by the
flashing LED).
The reason of this is that it is necessary to locate
the source of the alarm before using the hush
function. This is to make sure that it is not a life
threatening situation.
10.
ADD EXTRA DEVICE:
All CAVIUS interconnected alarms within the
can be added to the system as
they run on the same frequency and use the same
data protocol.This means that the wireless system
can consist of a combination of smoke, heat, flood
etc.
Place all alarms into ‘Learn Mode’ and repeat
section 1.
Always test connection to all devices by repeating
test function section 6 after adding devices.
11.
LOW BATTERY SIGNAL:
Your product has a 10Y battery life.
When the battery is starting its end of life, a short
beep will sound out every 48 seconds for 30 days.
The alarm affected by the low battery will only
beep, no other connected alarms will sound.
It is recommended to replace the smoke alarm
after 10 years, or if the alarm has suffered any
damage. The alarm is not active unless it is insert-
ed in the mounting base.
Always check the alarm after inserting in the
mounting base (allow a few seconds before test-
ing).
12.
MAINTENANCE & TROUBLE SHOOTING:
• The smoke alarm should be vacuum cleaned
once per quarter, to remove dust particles, and
it can be wiped with a damp cloth. (Do not open
the alarm).
• High humidity condensing which can be
resolved by drying the smoke alarm.
If the smoke alarm does not work when the test
button is pushed, the probable cause is a faulty
battery. Check if the battery is worn out by push-
ing the test button
If the problem continues, please visit www.cavius.
com for any trouble shooting.
13.
OTHER INFORMATION:
Do not paint the alarm.
Note the local country regulations regarding
installation.
Disposal: please dispose properly at the end of
life. This is electronic waste which should be re-
cycled.
Please note local regulations about information
to your insurance company regarding installed
smoke alarms.
The CE mark affixed to this product confirms its
compliance with the European Directives which
apply to the product and, in particular, its compliance
with the harmonized specifications of standard
EN 14604 relating to Construction Products
Regulation 305/2011.
All Rights reserved: CAVIUS Aps assumes no
responsi bility for any errors, which may appear in
this manual. Furthermore, CAVIUS Aps reserves
the right to alter the hardware, software, and/or
specifications detailed herein at any time without
notice, and CAVIUS Aps does not make any com-
mitment to update the infor mation contained here-
in. All the trademarks listed herein are owned by
their respective owners. Copy right © CAVIUS Aps.
Once the mounting base is installed, attach the
alarm by twisting clockwise until it clicks. If the bat-
tery is either missing or inserted incorrectly, or the
switch is in ‘Learn Mode’, the smoke alarm will not
be able to click into the mounting base.
6.
TEST FUNCTION:
After installation, and at least once per quarter,
test all of your alarms to ensure they are operating
correctly and are within range of each other.
It is recommended to check visually every week if
the LED flashes correctly (every 48sec.)
Press the test button on any alarm for at least
10 seconds. This will send out a test signal
from the alarm; all other connected alarms
should receive the signal within a short time.
The alarms will emit a short beep and the
LED will flash every 8 seconds for 2 minutes
.
NOTE: Test function also allows to send a deplet-
ed RF signal to ensure an optimal operation in
normal conditions.
When the test signal is sent out, the alarms will
respond in two ways:
1. A single beep every 8 seconds indicates that the
alarms are connected and functioning.
2. Three short beeps every 8 seconds indicates a
smoke sensor fault. The alarm should be cleaned
by running the vacuum (on a low setting) around
the smoke alarm chamber and tested again.
If required this indication can be stopped early on
each alarm by a short press of the test button.
TIP: It is safe to cover the sound output hole with
your finger during the testing to minimize the
sound level emitted.
If the problem continues, please visit www.cavius.
com for any trouble shooting.
7.
NORMAL MODE:
In normal mode the LED will flash every 48 seconds
to show correct operation.
8.
ALARM MODE:
When a concentration of smoke is detected, the
smoke alarm will go into ‘Alarm Mode’. It will
sound the alarm signal and the LED will flash.
The smoke alarm will also transmit the alarm sig-
nal to the other connected alarms, which will also
sound the alarm signal after a short delay.
The CAVIUS Wireless Family have two different
alarm signals:
Alarm signal 1 (--- --- ---) is life threatening
alarms, like a smoke alarm.
CLICK THE SMOKE
ALARM FIRMLY INTO THE
BASE TO LOCK
0333
19
Download DoP document: www.cavius.com
EN 14604:2005 + AC :2008
DoP no.: 2106-003
127462rev1
Developed by CAVIUS Aps Julsøvej 16, DK-8600
Manufactured in P.R.C.
HEAT ALARM
SMART REMOTE
FLOOD ALARM
SMOKE ALARM
MAINS POWERED
SMOKE ALARM
