Cattron Remtron 22R08A User Manual Download Page 23

Page: 23 / 26

CommandPro

General Purpose & Safety Applications

User Manual

9M02-9028-A031-EN
Rev 4

7.4

Receiver Repairs

WARNING

Remove external power to the receiver enclosure before performing electrical work inside the
cabinet.

Refer to

Figure 5

7.4.1 Replacing the RF/Relay Board

1. Switch off power to the receiver and open the enclosure door.
2. Unplug the RF coax connector by pulling straight up and gently twisting back and forth. Remove the

grounding strap. Unplug all of the electrical connectors.

3. Remove the four screws from the corners of the receiver assembly mounting plate and remove the

assembly from the enclosure.

4. Replace in reverse order.

7.4.2 Changing the Receiver Identity Code

1. Using the RAC16A Series Programmer, attach the programming plug to the 6-pin connector on the

receiver circuit board. Verify the ID CODE is displayed.

2. Enter the new Identity Code and press the PRG key.
3. Remove the programming plug.

Note:

Refer to the RAC16A Series Programmer

User’s Manual for more detailed instructions.

7.5

Receiver Specifications

Item

Detail

Power Requirements

Standard

12-24 VDC (11 VDC to 14 VDC)

Optional

24, 115 or 230 VAC, 1 phase, 50/60Hz

Receiver Type

Dual Conversion FM

Sensitivity

1 µV usable

IF Bandwidth

180 KHz

Antenna

3” tuned element

Decoder

Microprocessor-controlled

Response Time

60 milliseconds

Summary of Contents for Remtron 22R08A



























Search results

Summary of Contents for Remtron 22R08A

Reviews:

Related manuals for Remtron 22R08A

Brands by name

Popular brands

Cattron Remtron 22R08A, User Manual

Search results

Summary of Contents for Remtron 22R08A

Reviews:

Related manuals for Remtron 22R08A

Brands by name

Popular brands