-5-
CONNECTION TO APPLIANCE
ź
Before connection, ensure that there is no debris caught
in the head of the gas cylinder, regulator, burner and bur-
ner ports. Spiders and insects can nest within and clog
the burner/venturi tube at the orifice. A clogged burner
can lead to a fire beneath the appliance.
ź
Clean burner holes with a heavy-duty pipe cleaner.
ź
Fit the hose to the appliance using a spanner to tighten it
onto the connection thread. If the hose is replaced it
must be secured to the appliance and regulator con-
nections with hose clips. Disconnect the regulator from
the cylinder (according to the directions supplied with
the regulator) when the barbecue is not in use.
ź
The Barbecue must be used in a well ventilated area.
Do not obstruct the flow of combustion air to the burner
when the barbecue is in use.
ź
ONLY USE THIS BARBECUE OUTDOORS.
BEFORE USE CHECK FOR LEAKS
Never check for leaks with a naked flame, always use
a soapy water solution
CHECK FOR LEAK
S
ź
Make 2-3 fluid ounces of leak detecting solution by
mixing one part washing up liquid with 3 parts water.
ź
Ensure the control valve is “OFF”.
ź
Connect the regulator to the cylinder and ON/OFF valve
to the burner, ensure the connections are secure then
turn ON the gas.
ź
Brush the soapy solution onto the hose and all joints. If
bubbles appear you have a leak, which must be rectified
before use.
ź
Retest after fixing the fault
ź
Turn OFF the gas at the cylinder after testing.
ź
If leakage is detected and cannot be rectified. Do not
attempt to cure leakage but consult your gas dealer.
LIGHTING YOUR BARBECUE - Lighting Instructions
ź
Open the hood.
ź
Turn all the control knobs clockwise to “OFF” position.
ź
Connect the regulator to the gas bottle. Turn the gas
supply “ON” at the regulator. Check with the use of
soapy water for any gas leakage between the bottle and
the regulator
ź
Push down the left hand control knob and turn it anti-
clockwise to the “Full rate” position whilst depressing the
piezo ignition button 4 or 5 times. This will light the bur-
ner. Observe if the burner has lit. If not repeat this pro-
cess.
ź
If the burner has not lit after retrying wait 5 minutes and
repeat step 4.
ź
Adjust the heat by turning the knob to the Max/Min positi-
on.
ź
If the burner does not light. Light the appliance with a
match using the lighting hole in the side of the appliance.
Consult your gas dealer to rectify the pilot ignition.
ź
To light the right hand burner, turn the right hand control
knob to the full rate position, it will light of the left hand
burner. Always light the appliance from the left hand bur-
ner to the right hand side.
ź
To turn the barbecue ‘OFF’ either turn the gas control
knobs to the ‘OFF’ position if the side burner is in use or
turn ‘OFF’ turn the cylinder valve or regulator switch to
the ‘OFF’ position if the barbecue process has been
finished and then turn the control knobs on the appliance
clockwise to the ‘OFF’ position.
Warning:
If the burner fails to ignite, turn the control knob off
(clockwise) and also turn the cylinder valve off. Wait five
minutes before attempting to relight with ignition sequence.
CLEANING AND CARE
CAUTION: All cleaning and maintenance should be
carried out when the barbecue is cool and with the fuel
supply turned OFF at the gas cylinder.
CLEANING
ź
Burning off the barbecue after every use (for approx 15
minutes) will keep excessive food residue to a minimum.
ź
OUTSIDE SURFACE
ź
Use mild detergent or baking soda and hot water soluti-
on. Non-abrasive scouring powder can be used on stub-
born stains, then rinse with water.
ź
If the inside surface of the barbecue lid has the appea-
rance of pealing paint, baked on grease build-up has
turned to carbon and is flaking off. Clean thoroughly
with strong hot soapy water solution. Rinse with water
and allow to completely dry.
ź
NEVER USE OVEN CLEANER.
INTERIOR OF BARBECUE BOTTOM
ź
Remove residue using brush, scraper and/or cleaning
pad, then wash with soapy water solution. Rinse with
water and allow to dry.
COOKING GRID
ź
Use a mild soapy water solution. Non-abrasive scouring
power can be used on stubborn stains then rinse with
water.
CLEANING THE BURNER ASSEMBLY
ź
Turn the gas OFF at the control knob and disconnect the
cylinder.
ź
Remove cooling grate.
ź
Clean the burner with a soft brush or blow clean with com-
pressed air and wipe with a cloth.
ź
Clean any clogged ports with a pipe cleaner or stiff wire
(such as an opened paper clip).
ź
Inspect burner for any damage (cracks or holes). If
damage is found, replace with a new burner. Reinstall
the burner, check to ensure that the Gas valve orifices
are correctly positioned and secured inside the burner
inlet (venturi).
SERVICE
ź
Your gas barbecue should be serviced annually by a
competent registered person.
Changes to text and technical parameters are reserved. Changes in text, design, and technical specifications are subject to change without notice and we reserve the
right to change them.
Art. No.
99BB011
e
Gas grill PARTY POINT
Summary of Contents for 99BB011
