background image

 

LEDs   

 
There are two sets of LED on the board, green and red.  Each LED has a label which Voltage it represents.  The green LED, 
when lit, indicates presence of the corresponding voltage.  The red LED, when lit, represent a short on the corresponding 
voltage at the output.  Please note that the green LEDs indicate presence of some voltage and do not necessarily indicate if 
the exact voltage is at the expected level. 
 

 

 

 

 

 

LED 

Purpose of LED 

D10 

-12V is present 

D11 

+12V is present 

D12 

+5V is present 

D13 

+3.3V is present 

D18 

+VIO is present 

D9  

-12V has a short or low voltage condition 

D15 

+12V has a short or low voltage condition 

D14 

+3.3V has a short or low voltage condition 

D16 

+5V has a short or low voltage condition 

 

5V 

ó

 3.3 V Translation 

PCIBX is capable of allowing 5V UUT to work with 3.3V system and vice versa, without any timing degridation.  Therefore 
cards or components needing 3.3 V signaling can be tested or operated on a 5-volt system using these extender cards. 
 
+5V cards can operate in +3.3V systems provided that +5V is provided to the UUT cards. 
 
If JP3 is installed the UUT signals will be the same as the bus signals, most 5V.  
If JP3 is not installed the signals between the bus and the UUT will be translated. 

 
 

 

 

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for PCIBX32-X
























Reviews: