EQ400I
ENGLISH
5.
CONTROL UNIT SETTING UP
Attention!!
POSITION THE DIPSWITCHES TO OFF DURING THE
1
ST
SETTING
-
UP PHASE EXCEPT FOR THE
D
IP
NR
8,
(
MAN
P
RESENT
),
THAT MUST BE SET TO
“ON”.
5.1
FUNCTIONS OF THE SWITCHES MOUNTED ON THE CARD
SW1
Re-closing operating logic
ON = Automatic
OFF = Manual
SW2
Final thrust
ON = Enabled
OFF = Disabled
SW3 Photocell
test
ON
= Enabled
OFF = Disabled
SW4
Motor absorption check
ON = Enabled
OFF = Disabled
SW5
Slow-down start limit-stop
ON = Enabled
OFF = Disabled
SW6
Flashing light logic
ON = Steady Light
OFF = Flashing light
SW7
Selects safety edge type
ON = Resistance edge
OFF = Mechanical edge
SW8
Man present
ON = Active
OFF = Inactive
5.2
SWITCHING ON THE CARD AND INSERTING THE PROGRAMMER/DISPLAY
•
Insert the programmer and power up the card.
•
The red mains present LED lights up and the
•
FW version appears on the display
5.3
USING THE PROGRAMMER AND PARAMETER MANAGEMENT.
Press OK to
Select the with
Press
to scroll until
proceed with the
the
arrows Setup
the parameters of
Input
programming.
Base menu and press
OK.
diagnostics
(
ACPS)
.
Note:
This function is for checking the state of the inputs on the board. Move in the pages and display all the inputs
with the arrows:
to go forward to the end and
to go back
Page
P2.1:
Buttons:
A
pre (Start),
Close
,
P
edestrian and
S
top
A
=Apre (Start),
C
=Close,
P
=Pedestrian,
S
=Stop
Values:
1
= Input closed, connected and active.
0
= Input open, not connected or deactivated.
Press
Page
P2.2:
Limit stop
: RA
: Opening slow-down,
RC
:
Closing slow-down,
FA
: Opening
, FC
: Closing
RA
= Opening slow-down start. (
FC Ral Start
),
RC
= Closing slow-down start (
FC Ral Close
)
FA
= Opening limit stop. (
FC Start
),
FC
= Closing limit stop (
FC Closing
)
Values:
1
= Input closed, connected and active.
0
= Input open, not connected or deactivated.
Press
Page
P2.3:
Safety edges
: CSAP=000
Edge opening Input.
CSCH=000
Edge Closing Input
Values:
255
=Input open,
0
= Input closed, Edge NC connected or resistance activated,
xxx
=resistance value of the type of edge connected (0 < value < 255).
Press
Page
P2.4.
Status of the DIP SWITCH present on the board:
12345678
Values:
0
switch off (OFF),
1
switch
on
(ON)
Press
Page
P2.5
L1
PAUS=XXX:
Pause time set. Displays the time adjusting the trimmer
TR1 (Pause)
L2
PAUS=xxx
= During the pause, shows the remaining time, that decreases starting from the set value until
reaching
0.
Press
Page
P2.6. FT =
Status of photocell input.
Values:
0
= Input open or photocell not connected,
1
= Input short circuited or photocell connected
Press
Page
P2.7
= Information on the slow-down point and thrust status (Internal information)
Press
Page
P2.8
= Relative position (Sec)
Values:
0.0
= Door closed, Limit stop activated. Decrease to closing
SS.s
= Door open, Limit stop activated. Increase to opening until reaching the value
set in RunTime (
P2.24
)
Pagina 4 di 9 Rev. 00 del 30/11/2009
