background image

7

8

POWER SCREW

1.  The power screw permits you to adjust the power. It has been adjusted before leaving the 

factory. However, if the voltage in your home is low, you may need to re-adjust it.

2.  To adjust, use a screwdriver or a thin coin to turn power screw in clockwise direction until the 

arm strikes the coil, making a noise. Then slowly turn power screw out (Anti-clockwise) until 
noise stops. This is maximum power setting.

BLADE LEVER

1.  The lever is conveniently located near your thumb (if you're right-handed) so it can easily be 

adjusted while the trimmer is in your hand.

2.  The lever adds versatility to your trimmer by allowing you to gradually change the closeness of 

your cut without an attachment comb.

3.  When the lever is in the uppermost position, the blades will give you the closest cut and leaves 

the hair very short. Pushing the lever downward gradually increases the cutting length.

4.  The lever will also extend the use of your blades since different cutting edge is used in each setting.
5.  In addition, if extremely heavy hair cutting has jammed the blades, it will help you remove hair 

that has become wedged between the two blades without removing  
the blades.

6.  While the trimmer is running, rapidly move the lever from "close cut" to "longer cut" a couple of 

times. Doing this each time after you have finished using your clipper help to keep the blades 
clear of hair. If your clipper stops cutting and this does not help, your cutting blades are dulled. 
Replace them with new blades.

Close cut

Longer cut

Summary of Contents for PR-803













Reviews: