background image

Service 

Bulletin NTR SB 026 96

Magnum Hitch Diagnostic Codes and Service Manual update

Page 9 of 26

ELECTRONIC HITCH PERFORMANCE CODE

CODE 

C

H

P

t

MODE SOLUTION

DEGRADED

Replace RAISE/LOWER switch.

AUSE

litch RAISE/LOWER switch circuit failed. If the

roblem 

IS 

intermittent the function is disabled until

he next engine startup.

est

 wire harness for damaged wires or

connectors.

T

Hitch drop speed circuit failure. Drop speed will be
set to mid-range. Maximum drop rate can be

achieved by using

 the LOWER MOMENTARY

position on the RAISE/LOWER switch.

DEGRADED

1

Replace the drop speed potentiometer.
Test wire harness for damaged wires or

connectors.

Hitch response speed circuit failure. DEGRADED Replace the hitch response speed

1

potentiomer.

Test wire harness for damaged wires or

connectors.

Hitch travel circuit failure. Travel will be set to DEGRADED
naximum. 

1

Replace the hitch travel speed

potentiometer.

rest wire harness for damaged wires or

connectors.

Lamp circuit failure. DEGRADED

1

Replace lamp.
lest wires to lamp for damaged wires or

connectors.

DEGRADED

1

Capture the hitch and lower the hitch.

Hitch position is above the upper limit. Hitch can
be lowered by the control lever or by the rear
remote switches.

Rear remote switches failure when:
1. The remotes are operated simultaneously.
2. A remote switch is operated before startup.
3. A remote switch is operated when the hitch is

against the lower travel limit.

4 Remote switch LOWER is activated when the

hitch is against the lower travel limit.

5 Remote switch RAISE is activated when the

hitch is against the upper travel limit.

DEGRADED Error code will stop when switch is

1 reieased.

LOWER MOMENTARY failure when:
1. LOWER MOMENTARY switch is operated

before startup.

2. LOWER MOMENTARY switch is operated with

the tractor in motion.

3. LOWER MOMENTARY switch is operated

when the hitch is against the lower travel limit.

DEGRADED Error code will stop when switch is

1 released.

Display circuit failure.

Test secondary panel

with one from another tractor

Summary of Contents for Magnum 7210



























Reviews: