Case 921E Service Manual Download

Page: 37 / 41

2000-15

Bur 5-5410

Issued 2-07

Printed in U.S.A.

STEP 78

BD07B240

Connect engine controller, torque mounting bolt to
2 Nm (18 pound inches). Install mounting bolt for
wiring harness clamp. Connect the grounding wires
to the side of the engine.

STEP 79

BD07A222

If loader is equipped with air conditioning, connect
the low pressure hose to the compressor.

STEP 80

BD07B236

Route the fuel hoses into position and install the
clamps mounting the fuel hoses.

STEP 81

BD07B213

Install mounting bolts and clamps securing the
heater hose and wiring harness. Connect heater
hose at bell housing side of engine.

STEP 82

BD07B231

Install mounting bolts and brackets. Connect the
grounding wires to the side of the engine block.

STEP 83

BD07B220

Install mounting bolts securing the heater hose and
alternator wiring harness.

Summary of Contents for 921E










































Search results

Summary of Contents for 921E

Reviews:

Related manuals for 921E

Brands by name

Popular brands

Case 921E, Service Manual

Search results

Summary of Contents for 921E

Reviews:

Related manuals for 921E

Brands by name

Popular brands