Case 48083741 Service Manual Download Page 26

Page: 26 / 61

INTRODUCTION

Consumables

821G Capacities and specifications

Engine

Type of oil

CASE AKCELA UNITEK NO. 1™ SBL CJ-4

Technical specifications

SAE 10W-40

API CJ-4

CASE CONSTRUCTION specifications

MAT3521

Type of oil

CASE AKCELA UNITEK NO. 1™ SSL CJ-4 SAE 0W-40

(cold weather)

Technical specifications

SAE 0W-40
API CJ-4

CASE CONSTRUCTION specifications

MAT3521

Capacity (with filter change)

13.25 L

(

14 US qt

)

Total capacity in system

15.1 L

(

16 US qt

)

Cooling system

Type of coolant

CASE AKCELA ACTIFULL™ OT EXTENDED LIFE
COOLANT

CASE CONSTRUCTION specifications

MAT3624

System capacity

30 L

(

32 US qt

)

Fuel system

System capacity

288 L

(

76 US gal

)

Hydraulic system

Type of fluid

CASE AKCELA HY-TRAN® ULTRACTION

Technical specifications

ISO VG-46

CASE CONSTRUCTION specifications

MAT 3540

Type of fluid

CASE AKCELA HY-TRAN® ULTRACTION SSL

(low temperature)

CASE CONSTRUCTION specifications

MAT 3541

Total system capacity

178 L

(

47 US gal

)

Reservoir capacity

90.8 L

(

24 US gal

)

Transmission

Type of oil

CASE AKCELA NEXPLORE™ FLUID

Technical specifications

SAE 10W - 30
API GL-4
ISO VG-32/46

CASE CONSTRUCTION specifications

MAT 3525

Service capacity - with filter change

34.1 L

(

36 US qt

)

Axles

Type of oil

CASE AKCELA TRANSAXLE FLUID 80W-140

Technical specifications

SAE 80W-140
API GL-4

CASE CONSTRUCTION specifications

MAT 3510

Front axle (Standard and Heavy Duty)

40 L

(

42.3 US qt

)

Rear axle (Standard and Heavy Duty)

40 L

(

42.3 US qt

)

Grease fittings, as required

CASE AKCELA MOLY GREASE

CASE CONSTRUCTION specifications

MAT3550

Grade C

48083741_EN 31/07/2018

Summary of Contents for 48083741






























































Search results

Summary of Contents for 48083741

Reviews:

Related manuals for 48083741

Brands by name

Popular brands

Case 48083741, Service Manual

Search results

Summary of Contents for 48083741

Reviews:

Related manuals for 48083741

Brands by name

Popular brands