Case IH FARMALL 40C Service Manual Download

Page: 4 / 51

Contents

INTRODUCTION

Engine....................................................................................... 10

[10.001] Engine and crankcase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1

[10.202] Air cleaners and lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2

[10.206] Fuel filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.3

[10.304] Engine lubrication system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.4

[10.400] Engine cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.5

[10.501] Exhaust Gas Recirculation (EGR) exhaust treatment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.6

Clutch ....................................................................................... 18

[18.100] Clutch mechanical release control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.1

[18.110] Clutch and components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.2

[18.112] Slip clutch or flywheel damper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3

Transmission.............................................................................. 21

[21.114] Mechanical transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.1

[21.140] Mechanical transmission internal components. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21.2

Front axle system ....................................................................... 25

[25.100] Powered front axle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.1

[25.102] Front bevel gear set and differential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.2

[25.108] Final drive hub, steering knuckles, and shafts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.3

[25.310] Final drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25.4

Rear axle system........................................................................ 27

[27.106] Rear bevel gear set and differential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.1

[27.120] Planetary and final drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27.2

Hydrostatic drive......................................................................... 29

[29.100] Transmission and steering hydrostatic control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29.1

[29.202] Hydrostatic transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29.2

47941906 16/03/2016

Find manuals at https://best-manuals.com

Summary of Contents for FARMALL 40C




















































Search results

Summary of Contents for FARMALL 40C

Reviews:

Related manuals for FARMALL 40C

Brands by name

Popular brands

Case IH FARMALL 40C, Service Manual

Search results

Summary of Contents for FARMALL 40C

Reviews:

Related manuals for FARMALL 40C

Brands by name

Popular brands