background image

4

IMPORTANT SAFETY WARNINGS

This is the safety alert symbol. It is used to alert you 

to potential personal injury hazards. Obey all safety 

messages that follow this symbol to avoid possible 

injury or death.

explosion

fire

toxic

 

fumes

hot

 

surface

flying

 

objects

injection

moving

 

parts

electric

 

shock

DANGER

This is indicates a hazard which, if not avoided, will result in serious 

injury or death. 

WARNING

This indicates a hazard which, if not avoided, will result in a severe injury or 

property damage. 

CAUTION

This indicates a hazard which, if not avoided, might result in a minor or 

moderate injury. 

NOTICE

This indicates a situation that could result in equipment damage or damage  

to other property. Ensure all safety messages are observed and adhered to. 

Hazard Symbols and Meanings

DANGER

• Always operate the pressure washer in a well-ventilated area free of flammable vapors, combustible 

dust, gases, or other combustible materials.

• Do not store the pressure washer near an open flame or any equipment such as a stove, furnace, water 

heater, etc., which utilizes a pilot light or sparking device.

• Do not use this pressure washer to spray flammable material.

• Do not smoke while filling burner fuel tank.

• Never fill the fuel tanks while the pressure washer is running or hot. Allow unit to cool for two minutes.

• Always refuel slowly to avoid the possibility of spilled fuel which may cause a risk of fire.

• Always leave room for fuel to expand in the gas tank. Do not overfill. 

• Engine Fuel Tank: If using a Gasoline Engine, refuel with gasoline only. Do not use diesel or kerosene.

• Burner Fuel Tank (Black): When refueling the Burner Fuel Tank, use No. 1 or No. 2 fuel oil/diesel or 

kerosene. Do not use gasoline.

• Do not operate the unit if gasoline or diesel fuel is spilled. Wipe the pressure washer clean and move it 

away from the spill. Avoid creating any ignition until the gasoline or diesel fuel has evaporated.

• When the battery is being activated, hydrogen and oxygen gases in the battery are extremely 

explosive. Keep open sparks and flames away from the battery at all times, especially when charging.

• Be certain to disconnect the battery ground terminal before servicing. When disconnecting the cable 

from the battery, start with the negative terminal. When connecting them, start with the positive cable.

• When charging the battery, remove the battery vent plugs.

• Use only a voltmeter or hydrometer to check a battery charge.

• DO NOT jump start the battery unless both batteries are of equal voltage and amperage.

Summary of Contents for C4013HGHG





























Reviews: