Page 4 of 6
ASSEMBLY INSTRUCTIONS (continued)
ASSEMBLY INSTRUCTIONS (continued)
● The shut-off delay is the length of time the light will stay at brightness after motion has ceased to be detected.
● You can set the shut-off delay by rotating the delay time knob arrow so it points to the desired time setting
within “TIME” range. To increase the shut-off delay, turn the knob clockwise.To decrease the shut-off delay, turn the
knob counterclockwise.
Shut-off Delay
Customization Options
After expiration of the TEST mode, the light will automatically enter AUTO mode and be on at low-level brightness
(0-50%).The light will turn to high-level brightness (100%) when motion is detected. When the motion stops, the
light will then revert to low-level brightness after the shut-off delay time you set ( 5 ~ 180 seconds).
●
●
●
● The light will turn off automatically at dawn.
Note: You can adjust the low level brightness (0~50%) by using the low level brightness knob. (See Fig. 6)
Fig.6
3. 6 HOURS (6H) MODE (nighttime operation only)
● The light will turn to high-level brightness (100%) at dusk, and will stay "ON" for 6 hours. The light will then
turn to low-level brightness. The light will turn to high-level brightness (100%) when motion is detected, and
will stay on as long as motion continues. When motion is no longer detected, the lights will remain on for the
predetermined shut-off delay time you set (5~180 seconds), and then turn to the predetermined low-level
brightness automatically.
● The light will turn off automatically at dawn.
Note: You can adjust the low level brightness (0~50%) by using the low level brightness knob. (See Fig. 6)
4. PHOTOCELL (PC) MODE (nighttime operation only)
● The light will brighten at dusk. It will turn off at dawn.
“AUTO” “3H”
or “6H” Mode
Manual
Override
Manual Override Operation Diagram
Turn wall switch OFF-ON
-OFF-ON in 0.5~3
Seconds
Turn wall switch OFF-ON
-OFF-ON in 0.5~3 Seconds
Fig. 7
5. Manual Override (nighttime operation only) (See Fig.7)
● To shift to the manual override mode, set the mode selector to “AUTO”, “3H” or “6H” mode. Turn the wall
switch “OFF”, and turn it “ON” twice within 3 seconds. The light will remain on all night long. To shift back to
“AUTO”, “3H” or “6H” mode, turn the wall switch “OFF”, and turn it “ON” twice within 3 seconds again.
● The light will turn off automatically at dawn.
Note: To make sure the above functions operate properly, always keep the wall switch in the “ON” position
(including the daytime).
FUNCTION AND OPERATION (continued)
Notes:
1. The sensitivity of the motion sensor will increase as the environmental temperature gets cooler. You may wish to
make adjustments when the season changes. For best performance, gently clean the lens with a soft cloth every 1
or 2 months to assure maximum sensitivity.
2. For best performance, install fixture at least 8 feet above the ground. At such a height, the fixture will provide a
detection distance of up to 70 feet at 77 degrees Fahrenheit. (See Fig.8)
3. The sensor detects movement across a detection range of 240 degrees. (See Fig.9)
4. The sensor will be more sensitive to motion across its detection path than motion directly towards it. (See Fig.10)
5. To reduce possible nuisances, do not mount the fixture near a heat source like an air conditioner, vent or furnace
exhaust, or in a direction facing any reflecting object or other light source.
2. 3 HOURS (3H) MODE (nighttime operation only)
The light will turn to high-level brightness (100%) at dusk, and will stay "ON" for 3 hours. The light will then turn to
low-level brightness. The light will turn to high-level brightness (100%) when motion is detected, and will stay on as
long as motion continues. When motion is no longer detected, the lights will remain on for the predetermined
shut-off delay time you set (5~180 seconds), and then turn to the predetermined low-level brightness automatically.
The light will turn off automatically at dawn.
Note: You can adjust the low level brightness (0~50%) by using the low level brightness knob. (See Fig. 6)
