Casals VSC65, Manual, Page: 7 / 76

7
Once you have finished using the appliance:
- Stop the appliance by releasing the on/off switch.
Maintenance and care
WARNING! Always unplug the machine before carrying
out work on it.
- Checking the saw blade: deposits of resin and glue
on the saw blade cause inefficient cutting. To avoid them,
always clean the blade immediately after use.
- Inspect the mounting screws: regularly inspect all the
mounting screws and ensure they are firmly tightened.
Should any screw be loose, tighten it immediately. Failure
to do so could put you at serious risk.
- Motor maintenance: always take the greatest care
over this and make sure that the motor winding is not
damaged and does not become wet with oil or water.
- The vents should always be kept clean and free of
obstacles.
- Clean the machine thoroughly after each use. Blast the
motor regularly with compressed air.
- Check that the mains lead is in good condition. If it
is not, take it to an Official Service Centre to have it
replaced.
Cleaning
- Disconnect the appliance from the mains and allow it
to cool before undertaking any cleaning task.
- Clean the electrical equipment and the mains
connection with a damp cloth and dry. DO NOT
IMMERSE IN WATER OR ANY OTHER LIQUID.
- Clean the equipment with a damp cloth with a few
drops of washing-up liquid and then dry.
- Do not use solvents, or products with an acid or base
pH such as bleach, or abrasive products, for cleaning
the appliance.
- Do not let water or any other liquid get into the air
vents to avoid damage to the inner parts of the
appliance.
- Never submerge the appliance in water or any other
liquid or place it under running water.
- If the appliance is not in good condition of cleanliness,
its surface may degrade and inexorably affect the
duration of the appliance’s useful life and could
become unsafe to use.
- CAUTION: There is a risk of fire if the appliance’s
cleaning is not done according to these instructions.
Supplies
- Always use original supplies, designed specifically
for your appliance model.
- These supplies are available in specialist shops.
Anomalies and repair
- Take the appliance to an authorised technical support
service if a product damage or other problems arise. Do
not try to dismantle or repair without assistance, as this
may be dangerous.
- If the connection to the mains has been damaged, it
must be replaced and you should proceed as you would
in the case of damage.
Specifications:
VSC65
- Rated power: 1200 W
- Rated Voltage: 230-240V~
- Rated Frequency: 50Hz
- No load Speed: 4500 rpm
- Max Blade diameter: Ø 185mm
- Max/min Blade width: 2.8/2.5mm
- Depth cut at 90º: 65 mm
- Depth cut at 45º: 45mm
- Depth setting: 0-65mm
- Inclination setting: 0-45º
- Weight: 3.5 Kg
- Sound Pressure level (LpA) = 97dB(A), KpA = 3dB
- Sound Power level (LwA) = 108dB(A), KWA = 3dB
- Inst. sound pressure level (LpCpeak) = 125dB(C), KpCpeak = 3dB
- Vibration = 3.5 m/s2, K= 1.5m/s2
- Not suitable for use in presence of flammable anaesthetic
mixture with air or with Oxygen or nitrous oxide
NB: These specifications are subject to change without
notice of purpose of improvement.
Measured sound level determined according EN60745.
The vibration emission level given in this information sheet
has been measured according EN60745 and may be
used to compare one tool with other. It may be used for a
preliminary assessment of exposure.
The vibration value during actual use of the power tool can
differ from the declared total value depending on the way
in which tool is used
For EU product versions and/or in case that it is
requested in your country:
Ecology and recyclability of the product
- The materials of which the packaging of this appliance
consists are included in a collection, classification and
recycling system. Should you wish to dispose of them,
1. Move the mobile guard (C) backwards and hold
it in place.
2. To loosen or tighten screw (E), block the screw
press by pushing block button (B).
3. Loosen the screw (E) and remove the setting
disc (D).
4. Fit the saw blade and tighten with the setting disc
(D) and the screw (E).
4.1 To adapt saw discs with a 30mm hole diameter,
first fit the washer that corresponds to the diameter
of the saw disc you are using, next the saw disc
and screw them into place with fastening disc D and
screw E.
5. Before fitting the new blade, make sure the
surfaces in contact with the setting discs are clean.
(The arrow printed on the fixed guard of the machine
indicates the cutting direction of the teeth).
6. Once the disc is fitted, check that the blocking
button (B) has returned to its original position due to
movement of the incorporated spring.
- In order to remove disc, follow the same steps as
indicated previously but in reverse order.
Dust extraction Assembly
- Always use the appliance with the dust collector
connected, inhaling dust is harmful to your health.
- Connect the vacuum aspirator suction tube to the dust
extraction adaptor (L)
Use:
Cutting depth setting
- To adjust the cutting depth, loosen the wing nut (F) and
move the base upwards or downwards. The scale printed
on the base indicates the cutting depth
Cutting angle setting
It can cut vertically and with an inclination of up to 45º.
The angle is adjusted by loosening the wing nut (J) and
according the scale printed on the base.
Cutting indication
The notch K is used as a cutting indication with the blade in
a vertical position or 45º. It is advisable to make test cuts.
Lateral stop adjustment
For parallel cutting, use the lateral stop (M). Cutting width
is adjusted with the scale or according to the plotting.
Tighten the wing nut (G) to work with the lateral stop.
- Connect the appliance to the mains.
- Press the locking button (H), and squeeze the trigger in
the on/off switch (I). When the on/off switch is released, the
machine stops.