W-75 WALL CONTROL
W-75SL Operates Downlights ONLY
W-75DL Operates Up and Downlights
BATTERY INSTALLATION
Open Battery Door
by pressing down
on the insert tab
provided.
Install a “MN21/A23”
12v alkaline batterie
in the space provided.
Please observe proper
polarity placement.
Replace Battery Door.
Battery
Door
12V
CHANGING FREQUENCY SETTING
You will only have to
change the dip switch
settings in the remote
if you are using more
than one fan in the same
area and want to control
them separately.
DIP SWITCHES
SET TO ‘111111’
(Factory Setting)
NOTE: DO NOT set dip switch setting in the remote to ‘000000’, this may cause
frequency interference from other Casablanca Products.All fans leave the factory set to
“111111”
(Figure 2)
(Figure 1)
12V
DIP SWITCHES
SET TO ‘000000’
To change frequency:
1. Turn power OFF at the circuit breaker or fuse box and at the
wall switch, for the fan you want to change.
2. Open the battery door and remove the battery as shown in
Figure #1
3. Change the dip switch settings, assuring that they are
match the Direct-Touch wall control. See Figure #2.
4. Re-install the battery with the proper polarity position and
the battery door.
5. At the circuit breaker or fuse box and at the wall switch,
turn the power on for the fan whose frequency you are
changing.
6. Within 20 seconds of restoring power to the ceiling fan
press and hold both the “1” and
reverse buttons as
shown in Figure #3. For 3 seconds, you will hear an audible
tone indicating the command has been accepted. The Fan
and Lights will be off. The frequency is now changed.
OPERATION SPEED CONTROL
There are five individual speed settings
for the fan. Each speed is indicated by the
number on the controller and an audible tone
for each speed.
To select the desired fan speed:
Press the number on the controller
corresponding to the speed desired. 4 is high,
3 medium, 2 low, 1 ultra-low, and 0 is off.
Note: It is normal for the fan to
start in the "High" position from
"Off" before changing to the selected
speed.
OPERATION REVERSING AIRFLOW
The direction of airflow can be changed from
downward to upward or from upward to downward.
To reverse the airflow:
1. Make sure the fan is on and blades are turning.
2. Press the
reverse button. You will hear a
series of clicks from the fan as it speeds up
before coming to a stop and changing direction.
OPERATION LIGHTS
To turn the lights off and on, press and
release the
button for either the up or
down lights for less than one second.
To dim either the up or down light, Press
and hold the
button for either the up or
down light for more than 1 second. The light
will come on at the last brightness setting
and increase in brightness until full power is
reached, then start dimming until the lowest
setting is reached. This cycle will repeat until
you release the light button.
Up Light
Down Light
Note: The dimming feature will only
work as long as the dimming feature
remains active. See "Operation CFL
mode".
Your fan has the ability to disable the
dimming feature to allow the use of CFL
bulbs.
To activate CFL mode:
1. Turn the fan off by using your wall switch.
2. Allow the fan to remain off for at least 5 seconds.
3. Turn the fan on by using your wall switch.
4. Immediately press and hold the "1" and "3" buttons for at least 5 seconds.
The fans lights will go to 100% brightness and the dimming function will
be disabled.
To cancel CFL mode:
5. Turn the fan off by using your wall switch. Allow the fan to remain off for
at least 5 seconds.
6. Turn the fan on by using your wall switch.
7. Immediately press and hold the "2" and "4" buttons for at least 5 seconds.
The fans lights will dim to 50% brightness and the dimming function will
be enabled. Press and hold the light buttons until the desired dimmer
setting is reached.
Caution: CFL bulbs will not
function properly when
dimmed, which may result
in flickering or reduced bulb
life.
OPERATION CFL MODE
AUTOMATIC DEMONSTRATION PROGRAM
Programmed into every Direct-Touch fan is an Automatic Demonstration
Program. It can be used to fully demonstrate
and test the operation of the fan.
To enter the demonstration program:
1. Turn the fan off for at least 5 seconds by
using your wall switch. This will clear the
fan memory ready for programming.
2. Turn the fan on by using your wall switch.
3. Immediately hold the "0" button for at least 5 seconds.
A multi-tone signal will verify the start of the test program. The fan and lights
will go through a series of changing fan speeds, reversing the fan operation
mode, turning off/on, and dimming the lights.
The complete cycle lasts slightly over one minute. It will continue to repeat
until the wall switch is turned off for more than five seconds, cancelling the
program.
Note: With CFL mode active,
the lights will not dim.
OPERATION SAFE-EXIT®
The Safe-Exit Program gives you about thirty
seconds of light when you turn the lights off,
enabling you to exit your home before the lights go
out. To enter the Safe-Exit Program:
1. Turn the fan off by using your wall switch.
Allow the fan to remain off for at least 5
seconds.
2. Turn the Power on. Immediately press and hold the "4" button for 5
seconds. When a light button is pressed, an audio tone and series of
lights blinking will indicate the program is active.
3. With CFL mode disabled, Pressing a Light Button will cause the lights to
stay on at 50% brightness for 20 seconds then decrease in intensity for 30
seconds then turn off.
4. With CFL mode active, Pressing a Light Button will turn the lights off after
30 seconds.
5. To cancel the Safe-Exit Program, turn off power off using your wall switch
and leave off for five seconds.
Safe-Exit
The Light-Minder Program automatically turns OFF
the fan mounted lights after two hours. To enter the
Light-Minder Program:
1. To operate the lights for Light Minder Program
Turn the fan off by using your wall switch.
Allow the fan to remain off for at least 5
seconds.
2. Turn the Power on. Immediately press and
hold the "1" button for 5 seconds. A series of
tones will be heard indicating the command
has been accepted. Once the lights turn on,
they will automatically turn off after 2 hours.
3. If you leave the room and turn OFF the lights, the lights will blink to
indicate the Light Minder command has been accepted. The lights will
stay on for 2 hours and then begin to dim. After thirty seconds have
elapsed, the lights will turn completely off. In CFL Mode, the lights will
not dim, but shut off after 2 hours.
4. To cancel the Light Minder Program, turn off power off using your wall
switch and leave off for five seconds.
LIGHT-MINDER® PROGRAM
Light-Minder
