background image

UNPACKING AND INSPECTION 

 
 

 

 

 

 

 

1.  Remove the cabinet from shipping carton, ensuring that all packing 

materials and protective plastic has been removed from the unit.  

2.  Inspect all components for completeness and condition.  

3.  If any freight damage is present, a freight claim must be filed imme-

diately with the shipping company.   

4. 

Freight damage is not covered under warranty

.  

5.  Check to insure all components are included: cabinet, instruction 

packet, mounting brackets and additional accessories, where appli-
cable. 

6.  Read operation instructions completely. 

7.  Appliance should be thoroughly cleaned before use.  See CLEAN-

ING INSTRUCTIONS in this manual (page 8). 

This appliance 
should be  
thoroughly 

cleaned prior to use.  
 
See the CLEANING         
INSTRUCTIONS in  
this manual. 

 
NOTE:  DO NOT 

discard 

the carton or other     
packing materials until 
you have inspected the 
appliance for hidden  
damage and checked it 
for proper operation.  
 
Refer to 

FREIGHT     

DAMAGE CLAIM          
PROCEDURE 

on            

bottom of this page. 

FREIGHT DAMAGE CLAIM PROCEDURE 

 
NOTE:  

For your protection, please note that equipment in this shipment was carefully inspected 

and packaged by skilled personnel before leaving the factory.  Upon acceptance of this shipment, 
the transportation company assumes full responsibility for its safe delivery. 
 

IF SHIPMENT ARRIVES DAMAGED: 

1. 

VISIBLE LOSS OR DAMAGE: 

Be certain that any visible loss or damage is noted on the freight 

bill or express receipt, and that the note of loss or damage is signed by the delivery person. 

2. 

FILE CLAIM FOR DAMAGE IMMEDIATELY:  

Regardless of the extent of damage. 

Contact 

your dealer immediately.

 

3. 

CONCEALED DAMAGE:

  If damage is unnoticed until the merchandise is unpacked, notify the 

transportation company or carrier immediately, and then file a “CONCEALED DAMAGE” claim 
with them.  This should be done within fifteen (15) days from the date the delivery was made to 
you.  

Be sure to retain the container for inspection

 
Carter-Hoffmann cannot assume liability for damage or loss incurred in transit, 

freight damage is 

not covered under warranty

. We will, however, at your request, supply you with the necessary 

documents to support your claim.

    

 

Summary of Contents for EVOL208














Reviews: