Carrier XPOWER 38VYX110 Installation Manual Download

Page: 3 / 14

GB - 2

38VYX110/38VYX130

General information

Precautions for safety

The unit must be installed according to the national plant-
engineering standards.
• Read this “PRECAUTIONS FOR SAFETY” carefully before

Installation.

• The precautions described below include the important items

regarding safety. Observe them without fail.

• After the installation work, perform a trial operation to check for

any problem.
Follow the Owner’s Manual to explain how to use and maintain the
unit to the customer.

• Turn off the main power supply switch (or breaker) before the unit

maintenance.

• Ask the customer to keep the Installation Manual together with the

Owner’s Manual.

CAUTION:

• This air conditioner adopts the new HFC refrigerant (R410A)

which does not destroy ozone layer.
The characteristics of R410A refrigerant are ; easy to absorb
water, oxidizing membrane or oil, and its pressure is approx. 1.6
times higher than that of refrigerant R22.
Accompanied with the new refrigerant, refrigerating oil has also
been changed.
Therefore, during installation work, be sure that water, dust,
former refrigerant, or refrigerating oil does not enter the
refrigerating cycle.
To prevent charging an incorrect refrigerant and refrigerating oil,
the sizes of connecting sections of charging port of the main unit
and installation tools are charged from those for the conventional
refrigerant. Accordingly the exclusive tools are required for the
new refrigerant (R410A).

• Connect indoor and outdoor units with field-supplied copper pipes

by means of flare connections. Use insulated seamless
refrigeration grade pipe only, (Cu DHP type according to
ISO1337), degreased and deoxidized, suitable for operating
pressures of at least 4200 kPa and for burst pressure of at least
20700 kPa. Under no circumstances must sanitary type copper
pipe be used.
Moreover, do not use the existing piping because there are
problems with pressure-resistance force and impurity in it.

• Check that the impedance of the mains power supply is in

conformance with the unit power input indicated in the
electric data (EN 61000-3-11).

• This unit complies with low-voltage (EEC/73/23) and electro-

magnetic compatibility (EEC/89/336) directives.

• This appliance must be connected to the main power supply by

means of a switch with a contact separation of at least 3 mm.
The installation fuse (25A D type

) must be used for

the power supply line of this conditioner.

WARNING:
• Ask an authorized dealer or qualified installation professional to

install/maintain the air conditioner. Inappropriate installation may
result in water leakage, electric shock or fire.

• Turn off the main power supply switch or breaker before attempting

any electrical work. Make sure all power switches are off. Failure
to do so may cause electric shock.

• Connect the connecting cable correctly. If the connecting cable is

connected in a wrong way, electric parts may be damaged.

• When moving the air conditioner for the installation into another

place, be very careful not to enter any gaseous matter other than
the specified refrigerant into the refrigeration cycle.
If air or any other gas is mixed in the refrigerant, the gas pressure
in the refrigeration cycle becomes abnormally high and it may
cause pipe burst and injuries on persons.

• Do not modify this unit by removing any of the safety guards or by

by-passing any of the safety interlock switches.

• Exposure of unit to water or other moisture before installation may

cause a short-circuit of electrical parts. Do not store it in a wet
basement or expose to rain or water.

• After unpacking the unit, examine it carefully for possible damage.
• Do not install in a place that might increase the vibration of the unit.
• To avoid personal injury (with sharp edges), be careful when

handling parts.

• Perform installation work properly according to the Installation

Manual.
Inappropriate installation may result in water leakage, electric
shock or fire.

• When the air conditioner is installed in a small room, provide

appropriate measures to ensure that the concentration of
refrigerant leakage occurred in the room does not exceed the
critical level.

• Install the air conditioner securely in a location where the base

can sustain the weight adequately.

• Perform the specified installation work to guard against an

earthquake.
If the air conditioner is not installed correctly, accidents may occur
due to the falling unit.

• If refrigerant gas has leaked during the installation work, ventilate

the room immediately.
If the leaked refrigerant gas comes in contact with fire, noxious
gas may generate.

• After the installation work, confirm that refrigerant gas does not

leak. If refrigerant gas leaks into the room and flows near a fire
source, such as a cooking range, noxious gas might generate.

• Electrical work must be performed by a qualified electrician in

accordance with the Installation Manual.
Make sure the air conditioner uses an exclusive power supply. An
insufficient power supply capacity or inappropriate installation may
cause fire.

• Use the specified cables for wiring and connect them firmly to

the terminals.
To prevent external forces applied to the terminals from affecting
the terminals.

• Be sure to provide grounding. Do not connect ground wires to gas

pipes, water pipes, lightning rods or ground wires for telephone
cables.

• Conform to the regulations of the local electric company when

wiring the power supply.
Inappropriate grounding may cause electric shock.

• Do not install the air conditioner in a location subject to a risk of

exposure to a combustible gas.
If a combustible gas leaks, and stays around the unit, a fire may
occur.

Required tools for installation work

Philips screw driver

Cutter drill (65 mm)

Spanner