Carrier WeatherMaster Puron 48HC D17, Service And Maintenance Instructions, Page: 38 / 100

38
Gas Valve
All unit sizes are equipped with 2-stage gas valves. See Fig. 49
for locations of adjustment screws and features on the gas
valves.
Fig. 49 — Gas Valve
ADJUSTING GAS VALVE PRESSURE SETTINGS
CHECK UNIT OPERATION AND MAKE NECESSARY
ADJUSTMENTS
NOTE: Gas supply pressure at gas valve inlet must be within
specified ranges for fuel type and unit size. See Tables 9-12.
1. Shut off electrical power supplies to unit and install lock-
out tag.
2. Shut off manual gas shut off valve located on gas supply
line.
3. Remove manifold pressure tap plug from manifold and
connect pressure gage or manometer. See Fig. 47.
4. Turn on electrical supply.
5. Open manual shut off valve, then turn on unit main gas
valve.
6. Set room thermostat to call for heat. Verify high-stage heat
operation before attempting to adjust manifold pressure.
7. When main burners ignite, check all fittings, manifold,
and orifices for leaks.
8. Adjust high-stage pressure to specified setting by turning
the plastic adjustment screw clockwise to increase pres-
sure, counter-clockwise to decrease pressure.
9. Set room thermostat to call for low-stage heat. Adjust low-
stage pressure to specified setting.
10. Replace regulator cover screw(s) when finished.
11. With burner access panel removed, observe unit heating
operation in both high stage and low stage operation.
Observe burner flames to see if they are blue in
appearance, and that the flames are approximately the
same for each burner.
12. Turn off unit, close manual gas shut off valve, remove
pressure manometer and replace the 1 /
8
-in. pipe fitting on
the gas manifold. See Fig. 47.
BURNER IGNITION
Unit is equipped with a direct spark ignition 100% lockout sys-
tem. Integrated Gas Unit Controller (IGC) is located in the con-
trol box. See Fig. 48. The IGC contains a self-diagnostic LED
(light-emitting diode). A single LED (see Fig. 52) on the IGC
provides a visual display of operational or sequential problems
when the power supply is uninterrupted. When a break in power
occurs, the IGC will be reset, resulting in a loss of fault history,
and the indoor evaporator fan ON/OFF times will be reset. The
LED error code can be observed through the viewport. During
servicing, refer to the label on the control box cover or Table 13
for an explanation of LED error code descriptions.
* A 3 second pause exists between LED error code flashes. If more
than one error code exists, all applicable codes will be displayed in
numerical se
q uence.
If lockout occurs, unit can be reset by interrupting power sup-
ply to unit for at least 5 seconds.
ORIFICE REPLACEMENT
This unit uses orifice type LH32RFnnn (where nnn indicates
orifice reference size). When replacing unit orifices, order the
necessary parts through the Carrier Replacement Components
Division (RCD). See Table 14 for available orifice sizes. See
Table 15 and Fig. 51 and 52 for IGC wiring and connections. See
Tables 16 and 17 for orifice sizes for Natural Gas and LP fuel us-
age at various elevations above sea level. Never drill or plug ori-
fices for operation.
Check that each replacement orifice is tight at its threads into
the manifold pipe and that orifice projection does not exceed
maximum value. See Fig. 45.
IMPORTANT: Leak check (using a mixture of soapy water
or leak detection fluid) all gas connections including the
main service connection, gas valve, gas spuds, and mani-
fold pipe plug. All leaks must be repaired before firing unit.
PLASTIC ADJUST
SCREW (2)
REGULATOR SPRING (2)
(PROPANE - WHITE
NATURAL - SILVER)
LOW STAGE
GAS PRESSURE
REGULATOR
ADJUSTMENT
MANIFOLD
PRESSURE TAP
INLET
PRESSURE TAP
ON/OFF
SWITCH
REGULATOR
COVER SCREW (2)
NPT INLET
NPT OUTLET
IMPORTANT: Refer to Troubleshooting Tables 18 and 19
for additional information.
Table 13 — LED Error Code Description*
LED INDICATION
ERROR CODE
DESCRIPTION
ON Normal Operation
OFF Hardware Failure
2 Flashes Limit Switch Fault
3 Flashes Flame Sense Fault
4 Flashes 4 Consecutive Limit Switch Faults
5 Flashes Ignition Lockout Fault
6 Flashes Induced-Draft Motor Fault
7 Flashes Rollout Switch Fault
8 Flashes Internal Control Fault
9 Flashes Software Lockout
LEGEND
LED — Light Emitting Diode