Carrier TRANSICOLD 69UG15 Series Operation And Service Download Page 16

Page: 16 / 60

−

T-343

CONTROL

BOX

CONTROL

PANEL

1. Total Time Meter

2. Engine Start Alarm (Buzzer)

3. Water Temperature Gauge

4. Auto Restart Module

5. Oil Pressure Gauge

6. Ammeter

7. Engine Start/Intake Heater

Energized Light

8. Ignition Switch

9. Battery Charger Fuse or Circuit Breaker (CB5)

10. Ground Studs

11. Circuit Breaker (CB2)

12. Starter Relay (SR)

13. Low Coolant Relay (LR)

14. Intake Heater Relay (HR)

15. Safety Relay (S)

16. Circuit Breaker (CB3)

17. Speed Control Module

Figure 1-9 Auto Restart Control Box and Panel

Table 1-2 Auto Restart Preset Values

Indicator

Preset Value

Description

Overspeed

2100 RPM

Overspeed is the point at which the unit will signal for shutdown.

Crank Disconnect

700 RPM

Crank Disconnect is the point at which the auto restart module

senses the engine has started and will disengage the starter.

Shutdown Lockout

Delay

15 seconds

The oil pressure and water temperature inputs are ignored during

this 15 second delay (after start up).

Intake Heater Delay

30 seconds

preheat
3 minutes post

heat

The delay is used during start up. The intake heater delay begins

timing after the auto restart module signal is received. During the

entire delay, the intake heater circuit will be energized, an indicator

light will be illuminated, and an alarm will sound. When the delay

expires, the unit will crank.

Crank Attempts

18 attempts

A series of six attempts with three attempts in each series for a

total of 18 attempts, refer to Table 1-3, Auto Restart Sequencing.

Summary of Contents for TRANSICOLD 69UG15 Series





























































Search results

Summary of Contents for TRANSICOLD 69UG15 Series

Reviews:

Related manuals for TRANSICOLD 69UG15 Series

Brands by name

Popular brands

Carrier TRANSICOLD 69UG15 Series, Operation And Service

Search results

Summary of Contents for TRANSICOLD 69UG15 Series

Reviews:

Related manuals for TRANSICOLD 69UG15 Series

Brands by name

Popular brands