Carrier TRANSICOLD 69UG15 Series Operation And Service Download Page 20

Page: 20 / 60

−

T-343

1.9 UNIT SPECIFICATIONS

a. Fuel Tanks

Nominal Tank Sizes

Fill Capacity

Draw Capacity

50 Gallon Steel

52 gallons

(256 liters)

50 gallons*

(246 liters)

50 Gallon Aluminum

52 gallons

(256 liters)

50 gallons*

(246 liters)

65 Gallon Steel

67.5 gallons

(197 liters)

65 gallons*

(189 liters)

80 Gallon Aluminum

85 gallons

(322 liters)

80 gallons*

(303 liters)

*Allows for DOT required 5% vapor space

b. Weights

Battery

63 lb (28.6 kg)

Generator (A

−

280 lb (127 kg)

Engine (Dry)

−

without Accessories

434 lb (197 kg) Approximate

Unit (with 50 gal steel tank, dry)

1555 lb (705.3 kg)

Unit (with 50 gal aluminum tank, dry)

1485 lb (673.6 kg)

Unit (with 65 gal steel tank, dry)

1580 lb (716.7 kg)

Unit (with 80 gal aluminum tank, dry)

1545 lb (700.8 kg)

1.10 ENGINE DATA

a. Bore/Stroke

3.26 in. (38 mm) / 4.03 in. (102.4 mm)

b. Compression Ratio

21.5 : 1

c. Cylinders (Number)

Four

d. Displacement

135.2 cubic inches (2.22 liters)

e. Firing Order

−

f. Lubrication System

Oil Pressure Safety

Switch Setting

Opens

18 psig (1.27 kg/cm

)

Capacity

Engine

−

16.0 US quarts (15.1 liters), includes standard filter.

Oil Level Indicator

Dipstick in oil pan or fill cap

NOTE

To check oil level on engines with the dipstick mounted in the

fill cap, remove the cap and wipe the dipstick clean. Insert the

cap back onto the oil fill tube, then remove to check level. It is

not necessary to screw the cap back into the fill tube when

checking level. DO NOT add oil if level is within the “safe”

range. If needed, add oil to bring level within the “safe” range.

Screw cap fully into fill tube after checking level.

Lube Oil

Specification

Use a heavy duty lubricating oil conforming to American Pe-

troleum Institute (API) Service Classification CG, CH or CI,

Base Number 10 or above.

Lube Oil Viscosity

Outdoor Temperature

Fahrenheit

Centigrade

SAE

F to 45

−

C to 7

10W30

F and above

C and above

10W30 or 15W40

g. Fuel and Fuel Heater

Thermostat (FHT)

Winter

Summer

Diesel No. 1

Diesel No. 2

FHT

Close on temperature fall @ 45+/

−

6.5

F Open on temperature rise @ 75+/

−

6.5

Power Consumption: 150 Watts @ +/

−

10% at 14 VDC

h. Fuel Warmer

Coolant Temperature

Summary of Contents for TRANSICOLD 69UG15 Series





























































Search results

Summary of Contents for TRANSICOLD 69UG15 Series

Reviews:

Related manuals for TRANSICOLD 69UG15 Series

Brands by name

Popular brands

Carrier TRANSICOLD 69UG15 Series, Operation And Service

Search results

Summary of Contents for TRANSICOLD 69UG15 Series

Reviews:

Related manuals for TRANSICOLD 69UG15 Series

Brands by name

Popular brands