EN
ES
FR
INDOOR UNIT DISPLAY
Hi POWER (Green)
FILTER (Orange)
PRE. DEF (Preheat/Defrost)
(Orange)
TIMER (Yellow)
OPERATION (Green)
RESET button
2
Press
FIX
: Move the louver to the
desired vertical direction.
Press
SWING
: To continuously swing
the louver automatically and press
again to stop.
For horizontal direction, adjust
manually.
AIR FLOW DIRECTION
5
Note:
• Do not move the louver manually by others.
• The louver may automation positioning by some operation mode.
ONE-TOUCH
AUTOMATIC OPERATION
8
To automatically select cooling, heating, or fan only operation
1.
Press
MODE
: Select A.
2.
Press
TEMP
: Set the desired temperature.
7
Press the “ONE-TOUCH” button for fully automated operation that is
customized to the typical consumer preferences in your region of the world.
The customized settings control temperature air
fl
ow strength, air
fl
ow
direction and other settings to provide you alternate contact with “ONE-
TOUCH” of the button. If you prefer other settings you can select from the
many other operating functions of your unit.
Press
ONE-TOUCH
: Start the operation.
REMOTE CONTROL
6
PREPARATION BEFORE USE
3
Preparing Filters
1. Open the air inlet grille and remove the air
fi
lters.
2.
Attach
the
fi
lters. (see detail in the accessory sheet).
Loading Batteries
1. Remove the battery cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Clock Setup
1.
Push
CLOCK by tip of the pencil.
If timer indication is
fl
ashing, go to the next step 2.
2.
Press
ON
or
OFF
: adjust the time.
3.
Press
SET
: Set the time.
1. Push and hold CHK button on the Remote
Control by the tip of the pencil, “00” will be
shown on the display.
2.
Press
while pushing CHK .
Note:
1. Repeat above step to reset Remote
Control to be °F.
2. Operation mode and temperature
set will reset to initial setting after
change the temperature unit.
3. Default setting of Remote Control
from factory is °F.
PRESET
ONE-TOUCH
QUIET
SWING
ON
CHK
OFF
CLR
SET
FIX
Hi-POWER ECO
COMFORT
SLEEP
MODE
TEMP
FAN
Infrared signal emitter
Start/Stop button
Mode select button (MODE)
Temperature button (TEMP)
Fan speed button (FAN)
Swing louver button
(SWING)
Set louver button (FIX)
On timer button (ON)
Off timer button (OFF)
Sleep timer button (SLEEP)
Setup button (SET)
Clear button (CLR)
Memory and Preset button
(PRESET)
One-Touch button
(ONE-TOUCH)
High power button
(Hi-POWER)
Economy button (ECO)
Quiet button (QUIET)
b
Comfort sleep button
(COMFORT SLEEP)
Filter reset button (FILTER)
Clock Reset button (CLOCK)
Check button (CHK)
REMOTE CONTROL A-B SELECTION
4
To separate using of remote control for each indoor unit in case of 2 air
conditioners are installed adjacent to each other.
Remote Control B Setup.
1. Press RESET button on the indoor unit to turn the air conditioner ON.
2. Point the remote control at the indoor unit.
3. Push and hold CHK button on the Remote Control by the tip of the
pencil. “00” will be shown on the display.
4.
Press
MODE
while pushing CHK . “B” will show on the display and “00”
will disappear and the air conditioner will turn OFF. The Remote Control
B is memorized.
Note:
1. Repeat above step to reset Remote Control back to A.
2. Remote Control A have not “A” display.
3. Default setting of Remote Control from
factory is A.
SYSTEM CHARACTERISTICS
1
1. Three-minute time delay: To protect against frequent compressor starts.
2. Preheating operation: Warm up the unit for several minutes before
blowing warm air.
3. Warm air control: When the room temperature reaches the set
temperature, the fan speed is automatically reduced and the outdoor unit
will stop.
4. Automatic defrosting: Fans will stop during defrost operation.
5. Heating capacity: Heat is absorbed from outdoor and released into
the room. When the outdoor temperature is too low, use another
recommended heating apparatus in combination with the air conditioner.
6. Some minor cracking sound may occur when unit operating. This is
normal and is caused by expansion/contraction of plastic.
Note:
Item 2 to 5 for Heating model
Air conditioner operating conditions
Temp.
Operation
Outdoor Temperature
Room
Temperature
Heating
5°F ~ 75°F (–15°C ~ 24°C)
Less than 82°F (28°C)
Cooling
14°F ~ 115°F (–10°C ~ 46°C)
70°F ~ 90°F (21°C ~ 32°C)
Dry
14°F ~ 115°F (–10°C ~ 46°C)
62°F ~ 90°F (17°C ~ 32°C)
CLR
SET
“B” Display
“00” Display
1110650133-1-EN.indd 3
1/4/10 3:50:57 PM