![background image](http://html.mh-extra.com/html/carrier/pad324/pad324_installation-instructions-manual_2561426012.webp)
12
513 01 3103 00
Proceed as follows:
1.
Remove caps from low-- and high--pressure service fittings.
2.
Using hoses with valve core depressors, attach low-- and
high--pressure gauge hoses to low-- and high--pressure
service fittings, respectively.
3.
Start unit and let run until system pressures stabilize.
4.
Measure and record the following:
a.
Outdoor ambient--air temperature (5
°
F [5
°
C] db).
b.
Liquid line temperature (5
°
F [5
°
C]) at TXV.
c.
Discharge (high--side) pressure (psig).
d.
Suction (low--side) pressure (psig) (for reference only).
5.
Using Cooling Charging Charts compare outdoor--air
temperature (5
°
F [5
°
C] db) with the discharge line pressure
(psig) to determine desired system operating liquid line
temperature (See Fig. 18).
6.
Compare actual liquid line temperature with desired liquid
line temperature. Using a tolerance of +25
°
F (+1.15
°
C), add
refrigerant if actual temperature is more than 25
°
F (1.15
°
C)
higher than proper liquid line temperature, or remove
refrigerant if actual temperature is more than 25
°
F (1.15
°
C)
lower than required liquid line temperature.
NOTE
: If the problem causing the inaccurate readings is a
refrigerant leak, refer to Check for Refrigerant Leaks section.
AIRFLOW ADJUSTMENTS
UNIT OPERATION HAZARD
Failure to follow this caution may result in unit damage.
For cooling operation, the recommended airflow is 350 to
450 cfm for each 12,000 Btuh of rated cooling capacity. For
heating operation, the airflow must produce a temperature
rise that falls within the range stamped on the unit rating
plate.
CAUTION
!
NOTE
: Be sure that all supply--and return--air grilles are open,
free from obstructions, and adjusted properly.
ELECTRICAL SHOCK HAZARD
Failure to follow this warning could result in personal injury
or death.
Disconnect electrical power to the unit and install lockout
tag before changing blower speed.
!
WARNING
This unit is factory-set up for use with a single cooling fan speed.
In addition, this unit has the field-selectable capability to run two
different cooling fan speeds: The rated cooling fan speed
(350~400 CFM/Ton) and an enhanced dehumidification fan speed
(As low as 320 CFM/Ton) for use with either a dehumidistat or a
thermostat that supports dehumidification.
The cooling speed is marked “LOW” on the interface fan board
(IFB) (Fig. 11) . The factory-shipped settings are noted in Table 4.
There are 4 additional speed tap wires available for use in either
electric heating or cooling (For color coding on the indoor fan
motor leads, see Table 3). The additional 4 speed tap wires are
shipped loose with vinyl caps and are located in the control box,
near the interface fan board (IFB) (Fig. 11).
Single Cooling Fan Speed Set-up (Dehumidification feature
not used)
To change cooling speed:
1. Remove the vinyl cap off of the desired speed tap wire
(Refer to Table 3 for color coding). Add the wet coil
pressure drop in Table 5 to the system static to determine
the correct cooling airflow speed in Table 4 that will deliver
the nominal cooling airflow as listed in Table 1 for each size.
2. Remove the current speed tap wire from the “LOW” terminal
on the interface fan board (IFB) (Fig. 11) and place vinyl
cap over the connector on the wire.
3. Connect the desired speed tap wire to the “LOW” terminal
on the interface fan board (IFB).
NOTE
: If accessory electric heat is installed, and the electric heat
fan speed is chosen to be the same as the normal cooling fan
speed, the dry airflow must meet or exceed the minimum airflow
speed specified in Table 2 for the specific size unit.
Two Cooling Fan Speeds Set-up (Dehumidification feature
used)
IMPORTANT
: Dehumidification control must open control circuit
on humidity rise above set point.
Use of the dehumidification cooling fan speed requires use of
either a 24 VAC dehumidistat or a thermostat which includes
control of a 24 VAC dehumidistat connection. In either case, the
dehumidification control must open the control circuit on humidity
rise above the dehumidification set point. Dehumidification
controls are available with the reverse logic; these must not be
used.
1. Using Fig. 11, move the two pin DEHUM jumper from the
“STD” position to the “DEHUM” position.
2. Remove fan speed tap wire from the “LOW” terminal on the
interface fan board (IFB) (Fig. 11).
3. Determine correct normal cooling fan speed for unit and
application. Add the wet coil pressure drop in Table 5 to the
system static to determine the correct cooling airflow speed
in Table 4 that will deliver the nominal cooling airflow as
listed in Table 1 for each size.
NOTE
: If accessory electric heat is installed, the dry airflow must
meet or exceed the minimum airflow speed specified in Table 2 for
the specific size unit. The electric heat fan speed will be the same
as the normal cooling fan speed.
4. Remove the vinyl cap off of the desired speed tap wire
(Refer to Table 3 for color coding) for the normal cooling fan
speed and place desired speed tap wire on “HIGH” on the
interface board.
5. Refer to airflow tables (Table 4) to determine allowable
speeds for the dehumidification cooling fan speed. In Table
4, speeds that are not allowed for dehumidification cooling
are shaded.
6. Remove the vinyl cap off of the desired speed tap wire
(Refer to Table 3 for color coding) for the dehumidification
cooling fan speed and place desired speed tap wire on the
“LOW” connection on the interface board (IFB). Verify that
static pressure is in the acceptable range for the speed tap
to be used for dehumidification cooling.
7. Use any spare vinyl plugs to cap any unused speed tap
wires.