The manufacturer reserves the right to discontinue or change specifications or designs at any time without notice and without incurring obligations.
Note:
that a flashing fan symbol indicates that the fan within the air-
conditioner appliance is yet to switch ON.
General Operating Symbols
•
The thermometer on the display registers the current room
temperature with the small marker beside it indicating the
temperature that the heating/cooling system is currently set to
maintain.
•
The bar adjacent to the Key 1 button is displayed when continuous
fan operation has been enabled using the Key 1 button.
•
The Econ symbol is displayed when economy operation has been
enabled using the combination of the Function button immediately
followed by the Key 4 button
Note:
that the actual room temperature appears in the top right of the
display screen.
Note:
that “continuous” fan operation results in the fan being switched on
all the time to allow continuous circulation of air.
Note:
that the economy operation is only available for reverse-cycle air-
conditioning systems.
Manual Operation
•
Turn the Networker ON and press the Auto button until ‘Manual’
appears near the bottom left-hand corner of the screen. The Set
Temperature will now appear at the top of the screen with the current
room temperature still visible in the top right of the screen.
•
The Set Temperature is the temperature the air-conditioning system
is set to maintain. To alter it use the Rotary Dial to select the
temperature required.
•
Fan operation can be toggled between automatic and continuous
operation using the Key 1 button.
•
Where applicable, economy operation can be toggled on and off
using the combination of the Function button followed by the Key 4
button.
Where applicable the mode of operation can be cycled between heat
only, cool only and heating/cooling operation using the Mode button.
Note:
that the Networker limits the Set Temperature to a maximum of 30°C
and a minimum of 8°C. If the minimum is exceeded the air-conditioning
system is switched off and the Set Temperature indicated as ‘—‘.
Note:
that the Networker remembers your last settings, and goes back to
them the next time you select manual operation.
Auto Program Operation
In Auto Program mode the Networker allows you to preset your air-
conditioner to switch ON or OFF when you wake, leave, return and just
before you sleep. Settings that can be defined include:
•
The start time for the period.
•
The set temperature to be maintained.
•
Automatic or continuous fan operation.
•
The Mode of operation (where applicable).
•
Economy operation (where applicable).
In Auto Program mode the Networker has a pre-set Auto-Program for the
entire week the settings of which are defined in the table below.
Beginning Auto Program Operation
If the pre-set Auto-Program settings suit your lifestyle then all you need to
do is run the system in Auto Program mode by following these simple
steps:
•
Use the On/Off button to turn the Networker ON.
•
Use the Auto button until ‘Auto Program’ appears on the display
screen.
Temporarily Overriding the Auto-Program Settings
If these pre-set Auto-Program settings do not suit your lifestyle, you may
want to temporarily override them by simply using the Networker as you
would under manual operation, namely:
•
To alter the Set Temperature use the Rotary Dial to select the
temperature required.
•
To alter fan operation use the Key 1 button to toggle between
automatic and continuous operation.
•
To alter the economy setting use the combination of the Function
button followed by the Key 4 button to toggle the economy operation
on and off (where applicable).
•
To alter the operating mode use the Mode button to cycle between
heat only, cool only and heating/cooling operation (where applicable).
Period
Description
Temperature
Fan
Economy
Mode
Wake
Define the time and settings to operate your
system before you get up in the morning.
20°C AUTO OFF
HEAT/COOL
Leave
Define the time and settings to operate your
system when you have left for the day.
-- (OFF)
AUTO
OFF
HEAT/COOL
Return
Define the time and settings to operate your
system just before you get home.
20°C AUTO OFF
HEAT/COOL
Sleep
Define the time and settings to operate your
system at night.
-- (OFF)
AUTO
OFF
HEAT/COOL
FIG 5
FIG 7
FIG 6
Summary of Contents for Networker Wall Control
Page 1: ......
