background image

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Catalog No. 005-00042

Printed in U.S.A.

Form 50RHE-C1SI

Pg 1

2-04

Replaces: New

Book 1

4

Tab

5a 5a

Installation, Start-Up, and

Service Instructions

CONTENTS

Page

SAFETY CONSIDERATIONS

. . . . . . . . . . . . . . . . . . .1,2

GENERAL

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

INSTALLATION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16

Step 1 — Check Jobsite

. . . . . . . . . . . . . . . . . . . . . . . . 2

Step 2 — Check Unit

. . . . . . . . . . . . . . . . . . . . . . . . . . . 2

• STORAGE
• PROTECTION
• INSPECT UNIT

Step 3 — Unit Location

. . . . . . . . . . . . . . . . . . . . . . . . . . . 6

• FIELD CONVERSION OF DISCHARGE AIR

Step 4 — Mounting the Unit

. . . . . . . . . . . . . . . . . . . . . . 7

Step 5 — Duct System

. . . . . . . . . . . . . . . . . . . . . . . . . . . 7

• SOUND ATTENUATION
• EXISTING DUCT SYSTEM

Step 6 — Condensate Drain

. . . . . . . . . . . . . . . . . . . . . . 7

• VENTING

Step 7 — Piping Connections

. . . . . . . . . . . . . . . . . . . . 8

• WATER LOOP APPLICATIONS
• GROUND-WATER APPLICATIONS
• GROUND-LOOP APPLICATIONS

Step 8 — Electrical Wiring

. . . . . . . . . . . . . . . . . . . . . . . . 9

• POWER CONNECTION
• SUPPLY VOLTAGE
• 220-VOLT OPERATION
• PSC BLOWER SPEED SELECTION

Step 9 — Low Voltage Wiring

. . . . . . . . . . . . . . . . . . . . 16

• THERMOSTAT CONNECTIONS
• WATER FREEZE PROTECTION
• AIR COIL FREEZE PROTECTION
• ACCESSORY CONNECTIONS
• WATER SOLENOID VALVES

PRE-START-UP

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16,17

System Checkout

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

FIELD SELECTABLE INPUTS

. . . . . . . . . . . . . . . .17,18

C Control Jumper Settings

. . . . . . . . . . . . . . . . . . . . 17

C Control DIP Switches

. . . . . . . . . . . . . . . . . . . . . . . 17

D Control Jumper Settings

. . . . . . . . . . . . . . . . . . . . 17

D Control DIP Switches

. . . . . . . . . . . . . . . . . . . . . . . 17

D Control Accessory Relay Configurations

. . . . . 18

Water Valve (Slow Opening)

. . . . . . . . . . . . . . . . . . . 18

Outdoor Air Damper (OAD)

. . . . . . . . . . . . . . . . . . . . 18

START-UP

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-21

Operating Limits

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Scroll Compressor Rotation

. . . . . . . . . . . . . . . . . . . . . 19

Unit Start-Up Cooling Mode

. . . . . . . . . . . . . . . . . . . . . 19

Unit Start-Up Heating Mode

. . . . . . . . . . . . . . . . . . . . . 19

Flow Regulation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Flushing

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Antifreeze

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Cooling Tower/Boiler Systems

. . . . . . . . . . . . . . . . . . 21

Page

Ground Coupled, Closed Loop and Plateframe

Heat Exchanger Well Systems

. . . . . . . . . . . . . . . . 21

OPERATION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21,22

Power Up Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Units with Aquazone Complete C Control

. . . . . . . 21

Units with Aquazone Deluxe D Control

. . . . . . . . . . 21

SYSTEM TEST

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22,23

Test Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Retry Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Aquazone Deluxe D Control LED Indicators

. . . . . 23

SERVICE

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-25

Filters

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Water Coil

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Condensate Drain Pans

. . . . . . . . . . . . . . . . . . . . . . . . . 24

Refrigerant System

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Condensate Drain Cleaning

. . . . . . . . . . . . . . . . . . . . . 24

Air Coil Cleaning

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Condenser Cleaning

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Checking System Charge

. . . . . . . . . . . . . . . . . . . . . . . 24

Refrigerant Charging

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Air Coil Fan Motor Removal

. . . . . . . . . . . . . . . . . . . . . 25

TROUBLESHOOTING

. . . . . . . . . . . . . . . . . . . . . . . . 25-27

Thermistor

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Control Sensors

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

START-UP CHECKLIST

. . . . . . . . . . . . . . . . . . CL-1, CL-2

SAFETY CONSIDERATIONS

Installation and servicing of air-conditioning equipment can

be hazardous due to system pressure and electrical compo-
nents. Only trained and qualified service personnel should
install, repair, or service air-conditioning equipment.

Untrained personnel can perform basic maintenance func-

tions of cleaning coils and filters and replacing filters. All other
operations should be performed by trained service personnel.
When working on air-conditioning equipment, observe precau-
tions in the literature, tags and labels attached to the unit, and
other safety precautions that may apply.

Improper installation, adjustment, alteration, service, main-

tenance, or use can cause explosion, fire, electrical shock or
other conditions which may cause personal injury or property
damage. Consult a qualified installer, service agency, or your
distributor or branch for information or assistance. The
qualified installer or agency must use factory-authorized kits or
accessories when modifying this product. Refer to the individ-
ual instructions packaged with the kits or accessories when
installing.

IMPORTANT: Read the entire instruction manual before
starting installation.

Aquazone™

50RHE006-060

Water Source Heat Pumps

Horizontal Unit

50 Hz, CE Mark

R-407C

Summary of Contents for AQUAZONE 50RHE006

































Reviews: