Carrier AquaForce 30XW-V Installation, Operation And Maintenance Instructions Download Page 27

Page: 27 / 36

Options

No. Description

Advantages

Use for 30XW-V

range

Dual relief valves on 3-way

valve

194 Three-way valve upstream of dual relief valves

on the evaporator and the oil separator

Valve replacement and inspection

facilitated without refrigerant loss.

Comforms to European standard EN378/

BGVD4

580-1710

Compliance with Swiss

regulations

197

Additional tests on the water heat exchangers.

Additional supply of PED documents,

supplementary certificates and test certificates.

Conformance with Swiss regulations

580-1710

Compliance with Russian

regulations

199

EAC certification

Conformance with Russian regulations

580-1710

Compliance with Australian

regulations

200 Unit approved to Australian code

Conformance with Australian regulations

580-1710

Low noise level

257 Evaporator piping sound insulation

3 dB(A) quiter than standard unit

580-1710

Welded evaporator water

connection kit

266

Victaulic piping connections with welded joints.

Easy installation

580-1710

Welded condenser water

connection kit

267

Victaulic piping connections with welded joints.

Easy installation

580-1710

Flanged evaporator water

connection kit

268

Victaulic piping connections with flanged joints.

Easy installation

580-1710

Flanged condenser water

connection kit

269

Victaulic piping connections with flanged joints.

Easy installation

580-1710

Thermal compressor

insulation

271 The compressor is covered with a thermal

insulation layer

Prevents air humidity to condensate on the

compressor surface

580-1710

EMC classification C2, as per

EN 61800-3

282

Additional RFI filters on the unit power line

Reduces electromagnetic interferences.

Increase the variable frequency drive

(VFD) immunity level according to first

environment (so called, residential

environment) requirements and allow its

compliancy with emissions level required in

category C2

580-1710

Compliance with UAE

regulation

318

Additional label on the unit with rated power

input, rated current and EER following AHRI

550/590

Compliance with ESMA standard UAE.S

5010-5:2019.

580-1710

Compliance with Morocco

regulation

327

Specifics documents according Morroco

regulation

Conformance with Morocco regulations

580-1710

10 - OPTIONS

Summary of Contents for AquaForce 30XW-V





































Search results

Summary of Contents for AquaForce 30XW-V

Reviews:

Brands by name

Popular brands

Carrier AquaForce 30XW-V, Installation, Operation And Maintenance Instructions

Search results

Summary of Contents for AquaForce 30XW-V

Reviews:

Brands by name

Popular brands