Carrier 50PG08 14 Series Installation Instructions Manual Download Page 19

Page: 19 / 20

Step 7 — Install Outdoor Air Hoods (Units With

Economizer)

Perform the following procedure to install the outdoor--air hoods:

1. Economizer and barometric relief/power exhaust hoods are

located in the condenser section under the slanted coil for
shipping. (See Fig. 14.) Barometric relief/power exhaust

hood is shipped inside of economizer hood.

Remove

screws that secure the wooden rails of the hood assemblies
to the unit. Save screws. Slide complete assembly from

condenser section.

2. Remove the screws that secure the economizer and

barometric relief/power exhaust hoods to the wooden
railing. Discard or recycle wooden rails. Save screws.

3. The barometric relief damper is factory--mounted to the

economizer panel for shipping. Remove the screw holding
the barometric relief damper to the economizer panel.

Damper should be free to swing open during operation.
(See Fig. 15.)

BAROMETRIC
RELIEF HOOD

ECONOMIZER
HOOD

WOODEN RAILS

POWER EXHAUST/

C06290

Fig. 14 -- Economizer and Baromatric

Relief/Power Exhaust Hoods Shipping Positions

BAROMETRIC
RELIEF DAMPER SCREW

ECONOMIZER
HOOD

BAROMETRIC
RELIEF HOOD

ECONOMIZER
PANEL

POWER EXHAUST/

C06260

Fig. 15 -- Hood Installation

4. Hang the barometric relief/power exhaust hood on the

mounting flange on the economizer panel. Secure hood to

panel with screws saved from Step 2. (See Fig. 15 and 16.)

5. Align hole in flange of economizer panel with left edge of

hood. Hang economizer hood on the top flange of the

economizer panel by rotating hood until top flange of the
economizer hood engages the bent flange on the

economizer panel. Rotate hood until hood is flush with the
economizer panel. Hood will support itself from flange.
Align holes in hood with holes in panel and secure hood to

panel with screws saved from Step 2. (See Fig. 15 and 17.)

Step 8 — Install All Accessories

After all of the factory--installed options have been adjusted, install

all field--installed accessories. Refer to the accessory installation
instructions included with each accessory. Consult the Carrier

Price Pages for accessory package numbers for particular

applications.

Step 9 — Configure Controls

Refer to unit controls and Troubleshooting book for information

on configuring controls.

BAROMETRIC
RELIEF HOOD

MOUNTING
FLANGE

POWER EXHAUST/

C06262

Fig. 16 -- Barometric Relief/Power Exhaust

Hood Flange

MOUNTING

FLANGE

ECONOMIZER

HOOD

C06263

Fig. 17 -- Economizer Flange

50PG08

Summary of Contents for 50PG08 14 Series





















Search results

Summary of Contents for 50PG08 14 Series

Reviews:

Related manuals for 50PG08 14 Series

Brands by name

Popular brands

Carrier 50PG08 14 Series, Installation Instructions Manual

Search results

Summary of Contents for 50PG08 14 Series

Reviews:

Related manuals for 50PG08 14 Series

Brands by name

Popular brands