SERVICE
When servicing unit, shut off all electrical power to unit
to avoid shock hazard or injury from rotating parts.
Cleaning —
Inspect unit interior at the beginning of heat-
ing and cooling season and as operating conditions require.
EVAPORATOR COIL
1. Turn unit power off. Remove evaporator coil access panel.
2. If economizer is installed, remove economizer by dis-
connecting Molex plug and removing economizer mount-
ing screws. Refer to accessory economizer installation
instructions or Optional Economizer sections on pages 14
and 16 for more details.
3. Slide filters out of unit.
4. Clean coil using a commercial coil cleaner or dishwasher
detergent in a pressurized spray canister. Wash both sides
of coil and flush with clean water. For best results, back-
flush toward return-air section to remove foreign mate-
rial. Flush condensate pan after completion.
5. Reinstall economizer and filters.
6. Reconnect wiring.
7. Replace access panels.
CONDENSER COIL — Inspect coil monthly. Clean con-
denser coil annually, and as required by location and out-
door air conditions.
One-Row Coil Cleaning (sizes 004-006) — To access one-
row coils, remove screws securing condenser-fan grille to
condenser fan top cover. Place grille on top of condenser fan
top cover as shown in Fig. 36. It is not necessary to remove
the top cover.
Use a water hose or other suitable equipment to remove
dirt and debris. Clean the outer surfaces with a stiff brush in
the normal manner.
Reverse the procedure outlined above to reinstall the
condenser-fan grille and condenser fan top cover.
2-Row Coil Cleaning (size 007)
NOTE: Save all screws removed in this section. The screws
must be used when reinstalling the equipment.
1. To access 2-row coils, remove screws securing condenser-
fan grille to condenser coil top cover. Place grille on top
of condenser fan top cover as shown in Fig. 36 and 37.
It is not necessary to remove the top cover.
2. Remove 3 screws on right side of compressor access panel.
Remove one screw securing condenser coil top cover to
compressor access panel. Remove lower screw securing
condenser coil to compressor mounting plate.
3. Remove 4 screws securing control box access panel. Re-
move three screws (located in front of the control box
access cover) securing condenser coil top cover.
4. Remove screws securing low-voltage access panel. Re-
move 2 screws inside low-voltage access panel. Tilt sheet
metal (located on left side of low-voltage connections)
back 45 degrees.
5. Remove screw securing refrigerant service port access
panel.
6. Remove 2 wire ties securing 2-row coils together at hair-
pin end.
7. Remove screws securing two corner posts. Remove two
corner posts.
8. Use right corner post to prop up right side of condenser
coil top cover. Slide condenser coil partially out of con-
denser fan housing. See Fig. 37.
9. Use left corner post to prop up left side of condenser
coil top cover.
10. Carefully separate the outer coil section 3 to 4 in. from
the inner coil section. See Fig. 38.
11. Use a water hose or other suitable equipment to flush
down between the 2 coil sections to remove dirt and de-
bris. Clean the outer surfaces with a stiff brush in the
normal manner.
12. Secure inner and outer coils together with 2 wire ties.
13. Reposition the outer and inner coil section.
14. Reverse the procedure outlined above to reinstall
equipment.
CONDENSATE DRAIN — Check and clean each year at
start of cooling season. In winter, keep drain dry or protect
against freeze-up.
FILTERS — Clean or replace at start of each heating and
cooling season, or more often if operating conditions require
it. Replacement filters must be same dimensions as original
filters.
OUTDOOR-AIR INLET SCREENS — Clean screens with
steam or hot water and a mild detergent. Do not use dis-
posable filters in place of screens.
Fig. 36 — Coil Cleaning
Fig. 37 — Propping Up Condenser Coil
Top Cover
29
Summary of Contents for 48TJD Series
Page 40: ...Fig 47 Typical Wiring Diagram and Component Arrangement 40...
Page 41: ......
Page 43: ......
