![background image](http://html1.mh-extra.com/html/carrier/48aj-ak-amd020/48aj-ak-amd020_installation-instructions-manual_2560930043.webp)
43
11. Assemble 2 filter tracks side-by-side with the assembled
ends together.
12. Attach mounting angle (without tabs) to the assembled
end of the filter track. See Fig. 33.
13. Attach 9 green speed clips (provided) to hood side panels
without slots. Engagement section of clip faces up and to-
wards the outside of the hood side panels.
14. Attach remaining mounting angle (with tabs) to other end
of the filter track with no. 10 screws provided. See
Fig. 34.
15. Place filter track assembly in bottom of hood by placing
tabbed end into slotted side (with tab on bottom) and
attaching opposite end to hood with speed clips and
gasketed screws provided. Tabs can be hand bent after
they have been inserted into the side.
NOTE: The filter track assembly end with screws should face
away from the other hood when mounted on the unit. Be sure
the filters are installed with the airflow in the correct direction.
NOTE: Tabs from both filter tracks will be in the same space.
After one filter track has been inserted into hood side, bend the
tabs so they will not interfere with installation of the second/
center hood.
16. Attach black seal strip (provided) to filter cover. Seal strip
should be applied centered over the holes of the one
flange, making sure to fully cover holes and centered over
the other large flange. See Fig. 35.
17. Slide two 20 x 25-in. filters into cross members of hood
assembly. Attach filter cover over filters with screws and
speed clips provided.
18. Set Minimum Damper Position (MDP). See the Con-
trols, Start-Up, Operation, Service, and Troubleshooting
Instructions.
HOOD TOP
HOOD SIDE
CROSS MEMBER
GRAY FOAM STRIP
Fig. 29 — Adding Seal Strip to Back of Hood Top
Mounting Flange
Fig. 30 — Adding Foam Strip to Cross Member
HOOD SIDE
(SLOTTED)
HOOD
TOP
Fig. 31 — Adding Foam Strip to Hood Side
BLOCKOFF BAFFLE
GRAY FOAM STRIP
Fig. 32 — Adding Seal Strip to Blockoff Baffle
Summary of Contents for 48AJ/AK/AMD020
