background image

9

2.2 - Moving and siting the unit

2.2.1 - Moving

See chapter 1.1 “Installation safety considerations”.

CAUTION: Only use slings at the designated lifting 

points which are marked on the unit.

2.2.2 - Siting the unit

Always refer to the chapter “Dimensions and clearances” 

to confirm that there is adequate space for all connections 

and service operations. For the centre of gravity coordinates, 
the position of the unit mounting holes, and the weight 

distribution points, refer to the certified dimensional 

drawing supplied with the unit.

Typical applications of these units are in refrigeration 
systems, and they do not require earthquake resistance. 

Earthquake resistance has not been verified.

Before siting the unit check that:
• 

the permitted loading at the site is adequate or that 
appropriate strenghtening measures have been taken.

• 

the unit is installed level on an even surface (maximum 
tolerance is 5 mm in both axes).

• 

there is adequate space above the unit for air flow and 

to ensure access to the components.

• 

the number of support points is adequate and that they 
are in the right places.

• 

the location is not subject to flooding.

CAUTION: Lift and set down the unit  with great care. 
Tilting and jarring can damage the unit and impair unit 

operation.

2.2.3 - Checks before system start-up

Before the start-up of the refrigeration system, the complete 
installation, including the refrigeration system must be 

verified against the installation drawings, dimensional 

drawings, system piping and instrumentation diagrams and 
the wiring diagrams.

During the installation test national regulations must be 
followed. If no national regulation exists, standard EN 378 
can be used as a guide.

 External visual installation checks:
• 

Ensure that the machine is charged with refrigerant. 

Verify on the unit nameplate that the ‘fluid being 

transported’ is R-134a and is not nitrogen.

• 

Compare the complete installation with the refrigeration 
system and power circuit diagrams.

• 

Check that all components comply with the design 

specifications.

• 

Check that all protection documents and equipment 
provided by the manufacturer (dimensional drawings, 
P&ID, declarations etc.) to comply with the regulations 
are present.

• 

Verify that the environmental safety and protection and 
devices and arrangements provided by the manufacturer 
to comply with the regulations are in place.

• 

Verify that all document for pressure containers, certi-

ficates, name plates, files, instruction manuals provided 

by the manufacturer to comply with the regulations are 
present.

• 

Verify the free passage of access and safety routes.

• 

Check that ventilation in the plant room is adequate.

• 

Check that refrigerant detectors are present.

• 

Verify the instructions and directives to prevent the 
deliberate removal of refrigerant gases that are harmful 
to the environment.

• 

Verify the installation of connections.

• 

Verify the supports and fixing elements (materials, 

routing and connection).

• 

Verify the quality of welds and other joints.

• 

Check the protection against mechanical damage.

• 

Check the protection against heat.

• 

Check the protection of moving parts.

• 

Verify the accessibility for maintenance or repair and 
to check the piping.

• 

Verify the status of the valves.

• 

Verify the quality of the thermal insulation and of the 
vapour barriers.

Summary of Contents for 30XW





































Reviews: