Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Catalog No. 04-53300025-01
Printed in U.S.A.
Form 30HX-13SI
Pg 1
10-08
Replaces: 30HX-12SI
Installation Instructions
CONTENTS
Page
SAFETY CONSIDERATIONS
. . . . . . . . . . . . . . . . . . . . . . . .1
INTRODUCTION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
INSTALLATION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-41
Step 1 — Inspect Shipment
. . . . . . . . . . . . . . . . . . . . . . . . 1
Step 2 — Rig and Place Unit
. . . . . . . . . . . . . . . . . . . . . . . 16
Step 3 — Piping Connections
. . . . . . . . . . . . . . . . . . . . . .16
• COOLER FLUID, VENT, AND DRAIN
• BRINE UNITS
• PREPARATION FOR YEAR-ROUND OPERATION
• FILL FLUID LOOP
• INSULATE COOLER HEADS
• 30HXA PIPING, VALVE, AND FAN CYCLING
PRESSURE SWITCH INSTALLATION
• 30HXC PIPING AND VALVE INSTALLATION
• INSTALL PRESSURE RELIEF REFRIGERANT VENT
PIPING
Step 4 — Make Electrical Connections
. . . . . . . . . . . . .25
• FIELD POWER CONNECTIONS
• FIELD CONTROL POWER CONNECTIONS
• CONDENSER FAN CONTROL FOR CONDENSER
UNITS USED WITH 30HXA UNITS
Step 5 — Install Accessories
. . . . . . . . . . . . . . . . . . . . . . 27
• 30HXA LOW-AMBIENT OPERATION
• MINIMUM LOAD ACCESSORY
• MISCELLANEOUS ACCESSORIES
Step 6 — Leak Test Unit
. . . . . . . . . . . . . . . . . . . . . . . . . . . .27
• 30HXC UNITS
• 30HXA UNITS
Step 7 — Refrigerant Charge
. . . . . . . . . . . . . . . . . . . . . . .40
• 30HXC UNITS
• 30HXA UNITS
SAFETY CONSIDERATIONS
Installing, starting up, and servicing this equipment can
be hazardous due to system pressures, electrical components,
and equipment location. Only trained, qualified installers and
service mechanics should install, start up, and service this
equipment.
When working on the equipment, observe precautions in the
literature, and on tags, stickers, and labels attached to the
equipment.
• Follow all safety codes.
• Wear safety glasses and work gloves.
• Use care in handling, rigging, and setting bulky
equipment.
INTRODUCTION
These instructions cover installation of 30HX liquid chillers
with electronic controls and units with factory-installed options
(FIOPs).
INSTALLATION
Step 1 — Inspect Shipment —
Inspect unit for dam-
age upon arrival. If damage is found, immediately file a claim
with the shipping company. Verify proper unit delivery by
comparing the model number on the nameplate with the data in
Fig. 1. Do not store units in an area exposed to weather because
of sensitive control mechanisms and electronic devices.
Locate unit indoors. When considering unit location, con-
sult National Electrical Code (NEC, U.S.A.) and local code
requirements. Allow sufficient space for wiring, piping, and
service. Install unit in an area which will not be exposed to am-
bient temperatures below 50 F (10 C). See Fig. 2-10 for clear-
ance details.
Allow the following clearances for service access:
Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 ft (914 mm)
Rear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 ft (914 mm)
Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 ft (610 mm)
Ends . . . . . . . . . . . . . . . . . . . . . . tube length at one (either) end;
3 ft (914 mm) at opposite end.
Be sure surface beneath unit is level and is capable of
supporting the operating weight of the unit. See Fig. 11 and 12
and Tables 1A and 1B for unit mounting and operating
weights. If necessary, add supporting structure (steel beams or
reinforced concrete slabs) to floor to transfer weight to nearest
beams.
Instructions continued on page 16.
IMPORTANT: This equipment generates, uses, and can
radiate radio frequency energy. If not installed and used in
accordance with these instructions, this equipment may
cause radio interference. The equipment has been tested
and found to comply with the limits of a Class A comput-
ing device as defined by the FCC (Federal Communica-
tions Commission, U.S.A.) Regulations, Subpart J of Part
15, which are designed to provide reasonable protection
against such interference when operated in a commercial
environment.
30HXC 076 R - - 6 6 1 AA
Model Description
30HXA
—
Condenserless
Liquid Chiller
30HXC
—
Water-Cooled
Liquid Chiller
Nominal Size
076 126 186
086 136 206
096 146 246
106 161 261
116 171 271
Refrigerant/Cooler Options
L = Nitrogen with Minus 1-Pass Cooler
M = R-134a with Minus 1-Pass Cooler
N = Nitrogen with Standard Cooler
P = R-134a with Plus 1-Pass Cooler
Q = Nitrogen with Plus 1-Pass Cooler
R = R-134a with Standard Cooler
Electrical Options
- = Across The Line Start
A = Non-Fused Disconnect
Y = Y-Delta Starter
Z = Y-Delta and Non-Fused Disconnect
Factory-Installed
Option Codes*
AA — 1
BA — 2
CA — 3
KA — 1,2
LA — 1,3
TA — 2,3
ZB — 1,2,3
Packaging Code
1 = Standard Domestic
2 = Standard Export
Series
Voltage Code
1 = 575-3-60
2 = 380-3-60
4 = 230-3-60
5 = 280/230-3-60
6 = 460-3-60
8 = 230-3-50
9 = 380/415-3-50
Display Options
- = Navigator Display
E = Navigator Display with
Energy Management
*Option Code Descriptions:1 = Minimum Load Control, 2 = Suction Service
Valve, and 3 = Medium Temperature Brine
Fig. 1 — 30HX Identification
EVERGREEN
®
30HXA,HXC076-271
Water-Cooled and Condenserless
Liquid Chillers Series 6 with COMFORTLINK™ Controls
50/60 Hz
