background image

 

ULW Czech, s.r.o. 

V Ráji 34, Praha 9 

Hostavice, 198 00, CZ, IČO: 28256212, DIČ: CZ28256212

 

12.

 

Disclaimer 

12.1.

 

Unless explicitly stated for a specific Carpe Iter item (the Device, Holder, their accessories, 
brackets and other Carpe Iter equipment) 

(“

Item

”) 

otherwise, no testing or homologation 

procedures were taken to ensure compliance with regulations associated with using the 
Items in regular traffic 

 on the streets. Use at your own risk.  

12.2.

 

Make sure that Items with sharp edges are positioned so that the sharp edge does not face 
the rider. Always dismount Items, which you are not currently using 

 especially empty 

holders and brackets (which may form a sharp edge, when empty).  

12.3.

 

Even if the Items are mounted to your vehicle properly, you might suffer an injury to your 
body (bruises, tearing, fractures, etc.) or damage to your gear (tearing, breakage, etc.) 
especially in case of an accident (e.g. dismounting your vehicle in other than standard way).  

12.4.

 

Manuals and use instructions are only provided in electronic form and can be viewed 
and/or downloaded on our website. Manuals and instructions for use shall not be provided 
in printed form. 

12.5.

 

Our manuals and instructions for use assume casual experience with smart devices (such as 
smartphones) and basic manual dexterity. I case of doubt, installation of Items on a vehicle 
must be performed by a specialized workshop.  

12.6.

 

Manuals and instructions for use, as well as technical support are only provided in English.  

13.

 

Manufacturer’s 

Warranty 

13.1.

 

We provide world-wide warranty in the scope set forth below for defects, which exist upon 
delivery of an Item to the shipping address provided by you upon purchase and which shall 
manifest within the period of 2 year as of the date of the original purchase, if you are a 
consumer, and 1 year as of the date of the original purchase, if you are a business (you 
provided business identification number or VAT number upon purchase). This warranty 
does not apply to software and batteries (see below). The date of dispatch of an Item to 
your shipping address is deemed to represent the date of original purchase.  

13.2.

 

Limited 6 months warranty is provided for batteries included in an Item or, as the case may 
be, sold separately. In the course of this limited battery warranty we guarantee that the 
battery will retain at least 60% of its nominal capacity. No warranty is provided for batteries 
beyond the period of 6 months following the date of original purchase. Warranty for 
batteries is subject to adhering to the use instructions set forth above.   

13.3.

 

Our warranty only covers defects that preclude the use of an Item for its purpose. In view 
of the intended purpose of use of the Items, our warranty does not cover, in particular, 
defects of cosmetic nature, such as discoloration, paint fading, rusting that does not hinder 
the use, etc.   

13.4.

 

Our warranty is subject to adhering to manuals and use instructions published on our 
website or stated above in this manual for individual Items. Our warranty does not cover 
defects occurring due to misuse of Items and lack of their maintenance.  

13.5.

 

No warranty is provided for software.  

13.6.

 

No warranty is provided for defects occurring as a result of outside forces (abrasion, shock, 
water, pressure, vibration, UV light, etc.).  

Summary of Contents for v3





















Reviews: