Carp Sounder XRS ACC Operating Instructions Manual Download Page 23 | Manualshive

Page: 23 / 44

background image

Catsounder

XRS ACC Bite alarm:

Changing the battery:

Open your Cat sounder by loosening the two screws on

the back of the case. Replace the batteries with new

ones and close the housing again.

Required batteries: 2x LR03 1.5V AAA

Attention: When not in use remove batteries from the

bite alarm. The bite alarm consumes some power while

idle.

Troubleshooting:

No function: batteries empty, defective or inserted

incorrectly

Device can not be switched on, LED flickers red: Batteries

empty

No sound: press the (+) button

No radio transmission: The coding does not match.

«
...
21
22
23
24
25
...
»

Summary of Contents for XRS ACC













































Reviews:

No comments

Related manuals for XRS ACC

Brand: JBL Pages: 6

Brand: Jensen Pages: 12

VM9213 - Touch Screen MultiMedia Receiver

Brand: Jensen Pages: 62

Brand: Jensen Pages: 9

Brand: Jensen Pages: 22

JHD3510 - Heavy Duty CD Receiver

Brand: Jensen Pages: 2

VM8013HD - Screen MultiMedia Receiver

Brand: Jensen Pages: 78

Phase Linear UV10

Brand: Jensen Pages: 90

Brand: Duevi Pages: 4

XDOM RPL - PRODUCTSHEET

Brand: Ebode Pages: 24

Brand: Audi Pages: 35

Brand: CAME Pages: 24

Brand: Yaesu Pages: 20

Brand: Shure Pages: 4

Brand: Exsys Pages: 2

Brand: Wetekom Pages: 22

Brand: B&K Pages: 88

Brand: Icom Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands